High Brightness 10.1 inch 1024x600 IPS MIPI TFT Display - RFH1010J-AYH-MNN
High Brightness 10.1 inch 1024x600 IPS MIPI TFT Display - RFH1010J-AYH-MNN

High Brightness 10.1" 1024x600 IPS MIPI TFT Display

Model No. RFH1010J-AYH-MNN

RFH1010J-AYH-MNN is a 10.1-inch IPS TFT LCD module. It features high brightness and wide viewing angle (85/85/85/85 degree). This module uses EK79007AD3 and EK73217BCGA driver IC supports 4-Lanes MIPI Interface. The contrast ratio of the module is 800:1 (typical value), the brightness is 1100 nits (typical value), and the aspect ratio is 16:9. LCD voltage ranges from 1.71V-1.89V, typical value is 1.8V. Operating temperature covers from -20~+70℃, storage temperature range is from -30~+80℃.

Related products no.:
RFH1010J-AYH-MNN: Without Touch Screen
RFH1010J-AYH-MNB: With Projected Capacitive Touch Screen
RFH1010J-AYH-MNS: With Resistive Touch Screen

Inquiry or Demo Code Datasheet Back Previous Next
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
Item Dimension Unit
TFT Series IPS TFT LCD, High Brightness TFT
Size (Diagonal) 10.1 inch
Dot Matrix / Resolution 1024 RGB × 600 dots
Module Dimension 235(W) × 143(H) × 5.05(D) mm
Active Area 222.72 (H) × 125.28(V) mm
Dot / Pixel Pitch 0.2175(W) × 0.2088(H) mm
LCD Type TFT, Normally Black, Transmissive
View Direction 85/85/85/85 (IPS)
Aspect Ratio 16:9
Backlight Type LED, Normally White
Control Board No
TFT Driver IC EK79007AD3 + EK73217BCGA or equivalent
Interface 4-Lanes MIPI
Touch Panel Without Touch Panel
Surface Anti-Glare
Brightness 1100 cd/㎡
Mounting Hole No
Operating Temperature -20~+70 °C
Storage Temperature -30~+80 °C

TFT LCD Module

Pin No. Symbol Description
1 VLED+ LED Anode
2 VLED+ LED Anode
3 VGH Positive power for TFT
4 VGL Negative power for TFT
5 UPDN Gate up or down scan control.
UPDN = ”L”, STV2 output vertical start pulse and UD pin output logical “L” to Gate driver. (default)
UPDN = ”H”, STV1 output vertical start pulse and UD pin output logical “H” to Gate driver
6 SHLR Source right or left sequence control.
SHLR = ”L“, shift left: last data = S1←S2←S3….......←S1536 = first data.
SHLR = ”H“, shift right: first data = S1→S2→S3….....→S1536 = last data.(default)
7 VLED- LED Cathode
8 VLED- LED Cathode
9 AVDD Analog power
10 GND Digital ground
11 D3P MIPI data input.
12 D3N MIPI data input.
13 GND Digital ground
14 D2P MIPI data input.
15 D2N MIPI data input.
16 GND Digital ground
17 CLKP MIPI clock input
18 CLKN MIPI clock input
19 GND Digital ground
20 D1P MIPI data input.
21 D1N MIPI data input.
22 GND Digital ground
23 D0P MIPI data input.
24 D0N MIPI data input.
25 GND Digital ground
26 STBYB Standby mode.
STBYB = ”H“,normal operation(default)
STBYB = ”L”, timing controller, source driver will turn off, all output are GND.
27 RESET Global reset pin. Active Low to enter Reset State. Normally pull high. Connecting with an RC reset circuit for stability.
28 VDD (1.8V) Digital power
29 VDD (1.8V) Digital power
30 VCOMI Common voltage

 

 High Brightness 10.1 inch 1024x600 IPS MIPI TFT Display - RFH1010J-AYH-MNN

Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 － +70 ℃
Storage Temperature TST -30 － +80 ℃

Typical Operation Conditions (At Ta = 25 °C,)

Item Symbol Min Typ Max Unit
Digital Power Supply Voltage For LCD VDD  1.71 1.8 1.89 V
Analog Power Supply Voltage AVDD  9.89 10.2 10.5 V
Gate On Power Supply Voltage VGH  19.4 20 20.6 V
Gate Off Power Supply Voltage VGL  -10.3 -10 -9.7 V
Common Power Supply Voltage VCOMI 4 4.3 4.6 V

Related Products

Top