2 inch IPS High Brightness TFT LCD Display 240x320 (ST7789VI) - RFJ02000B-AYH-DNN
2 inch IPS High Brightness TFT LCD Display 240x320 (ST7789VI) - RFJ02000B-AYH-DNN

2 inch IPS High Brightness TFT LCD Display 240x320 (ST7789VI)

Model No. RFJ02000B-AYH-DNN

RFJ02000B-AYH-DNN is a 2-inch, IPS TFT LCD module with transmissive mode. The module dimension is 38.8x52.3 mm; active area 30.6x40.8 mm. Its resolution is 240x320 pixels and 3:4 aspect ratio. The module features wide viewing angle thanks to the IPS panel which is one of the most popular techniques on the market now, and viewing angle 80/80/80/80 degree.

This 2-inch TFT LCD display module use ST7789VI driver IC supporting MCU and SPI Interface. It also features high brightness, providing brightness 950 cd/m2 with contrast ratio (typical value) 800:1. Supply voltage for analog ranges from 2.4V-3.6V (typical value 3.3V). The module works within wide temperature range from-20 to +70℃，Storage Temperature covers from-30 to +80℃.

Inquiry or Demo Code Datasheet Back Next
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
Item Dimension Unit
TFT Series IPS TFT LCD, High Brightness TFT
Size (Diagonal) 2 inch
Dot Matrix / Resolution 240 × RGB × 320 (TFT) dots
Module Dimension 38.8(W) × 52.3(H) × 2.15(D) mm
Active Area 30.60 × 40.80 mm
Dot / Pixel Pitch 0.1275 × 0.1275 mm
LCD Type TFT, Normally Black, Transmissive
Viewing Angle 80/80/80/80 (IPS)
Aspect Ratio 3:4
Backlight Type LED, Normally White
Control Board No
TFT Driver IC ST7789VI or Equivalent
Interface MCU / SPI
Touch Panel Without Touch Panel
Surface Glare
Brightness 950 cd/㎡
Mounting Hole No
Operating Temperature -20~+70 °C
Storage Temperature -30~+80 °C
No. Symbol Function
1 GND Ground
2 NC No connection
3 NC No connection
4 NC No connection
5 NC No connection
6 NC No connection
7 VDD Power supply
8 VDDI Power Supply for I/O System.
9 TE Tearing effect signal is used to synchronize MCU to frame memory
writing.
If not used, please let this pin open
10 CSX Chip selection pin
Low enable.
High disable.
11 DCX(SCL) (D/CX): This pin is used to select “Data or Command” in the parallel interface.
DCX=’1’: display data or parameter.
DCX=’0’: command data.
(SCL): When SPI mode,This pin is used to be serial interface clock.
12 WRX(D/CX) Display data/command selection
Second Data lane in 2 data lane serial interface.
(WRX): Write enable in MCU parallel interface.
(D/CX): When 4-SPI mode,This pin in 4-line serial interface
If not used, please fix this pin at VDDI or GND.
13 RDX -Read enable in 8080 MCU parallel interface.
-If not used, please fix this pin at VDDI or GND.
14~29 DB0~DB15 Data bus line
30 RESX System reset pin.
signal is active low
31 IM0 The MCU interface mode select.
IM2 IM1 IM0 MPU Interface Mode Data pin
0 0 0 80-8bit parallel I/F DB[7:0]
0 0 1 80-16bit parallel I/F DB[15:0]
0 1 0 80-9bit parallel I/F DB[8:0]
0 1 1 80-18bit parallel I/F DB[17:0]
1 0 1 3-line 9bit serial I/F SDA: in/out
1 1 0 4-line 8bit serial I/F SDA: in/out
32 IM1
33 IM2
34~35 DB16~DB17 Data bus line
36 VLED- Cathode of LED backlight.
37 VLED- Cathode of LED backlight.
38 VLED+ Anode of LED backlight.
39 NC(SDA) When SPI mode, This pin is SPI interface input/output pin.
The data is latched on the rising edge of the SCL signal.
If not used(NC), please fix this pin at VDDI or GND level.
40 NC No connection

2 inch IPS High Brightness TFT LCD Display 240x320 (ST7789VI) - RFJ02000B-AYH-DNN

Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 － +70 ℃
Storage Temperature TST -30 － +80 ℃
Item Symbol Condition Min Typ Max Unit
Supply Voltage For Analog VDD － 2.4 3.3 3.6 V
Interface Operation Voltage VDDI － 1.65 1.8 3.6 V
Supply Current For LCM IDD VDD = VDDI
= VCC=3.0V		 － 6.0 9.0 mA

Related Products

Top