RFC350L-AIW-DNG - Raystar Optronics, Inc.

Item	Dimension	Unit
Size (Diagonal)	3.5	inch
Dot Matrix / Resolution	320 × RGB × 240 (TFT)	dots
Module Dimension	76.84 × 63.84 × 4.86	mm
View Area	71 × 53.51	mm
Active Area	70.08 × 52.56	mm
Dot / Pixel Pitch	0.073 × 0.219	mm
LCD Type	TFT, Normally White, Transmissive
View Direction	12 o’clock
Gray Scale Inversion Direction	6 o’clock
Aspect Ratio	4:3
Backlight Type	LED, Normally White
Control-Board	Option
TFT Driver IC	HX8238 or Equivalent
Interface	24-bit RGB Or option other mode
PCAP FW Version	0x07.0x00.0x00.0x00.0x00.0x35.0x5A.0x01
PCAP IC	ILI2130 or equivalent
PCAP Interface	I2C
PCAP Resolution	16384 × 1638
Detect Points	5	Points
Touch Panel	Projected capacitive touch panel, PCAP
Surface	Glare
Brightness	340	cd/㎡
Frame Through Hole	Option
Operating Temperature	-20~+70	°C
Storage Temperature	-30~+80	°C
TFT Series	Standard TFT LCD

Pin	Symbol	Function
1	LED-	Power for LED backlight cathode
2	LED-	Power for LED backlight cathode
3	LED+	Power for LED backlight anode
4	LED+	Power for LED backlight anode
5	NC	No connect
6	NC	No connect
7	NC	No connect
8	/RESET	Hardware reset
9	SPENA	Chip select pin of serial interface
10	SPCLK	Clock pin of serial interface (SPCK)
11	SPDAT	Data input pin in serial mode(SPDA)
12	B0	Data bus
13	B1	Data bus
14	B2	Data bus
15	B3	Data bus
16	B4	Data bus
17	B5	Data bus
18	B6	Data bus
19	B7	Data bus
20	G0	Data bus
21	G1	Data bus
22	G2	Data bus
23	G3	Data bus
24	G4	Data bus
25	G5	Data bus
26	G6	Data bus
27	G7	Data bus
28	R0	Data bus
29	R1	Data bus
30	R2	Data bus
31	R3	Data bus
32	R4	Data bus
33	R5	Data bus
34	R6	Data bus
35	R7	Data bus
36	HSYNC	Line synchronization signal
37	VSYNC	Frame synchronization signal
38	DCLK	Dot-clock signal and oscillator source
39	NC	No connect
40	NC	No connect
41	VCC	Power Supply
42	VCC	Power Supply
43~47	NC	No connect
48	SEL2	Input pin to select input interface mode
49	SEL1	Input pin to select input interface mode
50	SEL0	Input pin to select input interface mode
51	NC	No connect
52	DE	Display enable pin from controller. Internal pull high Connect to VDDIO or floating if not used
53	DGND	System ground pin of the IC. Connect to system ground.
54	AVSS	Grounding for analog circuit. Connect to system ground

Pin	Symbol	Function
1	VSS	Ground.
2	VDDT	Power Supply : +3.3V
3	SCL	I2C clock input
4	NC	No connect
5	SDA	I2C data input and output
6	NC	No connect
7	/RST	External Reset, Low is active
8	NC	No connect
9	/INT	External interrupt to the host
10	VSS	Ground.