- General Specs
- Interface Pin Function
- Contour Drawing
- Absolute Maximum Ratings
- Electrical Characteristics
Item | Dimension | Unit |
---|---|---|
TFT Series | TFT Panel with Controller Board,IPS TFT LCD | |
Size (Diagonal) | 4.3 | inch |
Dot Matrix / Resolution | 480 × RGB × 272 (TFT) | dots |
Module Dimension | 106.7 × 69.6 × 6.5 | mm |
Active Area | 95.04 × 53.856 | mm |
Dot / Pixel Pitch | 0.066 × 0.198 | mm |
LCD Type | TFT, Normally Black, Transmissive | |
View Direction | 80/80/80/80 (IPS) | |
Aspect Ratio | 16:9 | |
Backlight Type | LED, Normally White | |
Control Board | Yes | |
Built-in Controller | SSD1963 | |
Interface | Digital 8080 family MPU 8bit/16bit | |
Touch Panel | Without Touch Screen | |
Surface | Glare | |
Brightness | 500 | cd/㎡ |
O-Film | No | |
Mounting Hole | No | |
Operating Temperature | -20~+70 | °C |
Storage Temperature | -30~+80 | °C |
LCM PIN Definition (CON3)
Pin | Symbol | Function |
---|---|---|
1 | GND | System round pin of the IC. Connect to system ground. |
2 | VDD | Power Supply : +3.3V |
3 | BL_E | Backlight control signal , H: On \ L: Off |
4 | D/C | Data/Command select |
5 | WR | Write strobe signal |
6 | RD | Read strobe signal |
7 | DB0 | Data bus |
8 | DB1 | Data bus |
9 | DB2 | Data bus |
10 | DB3 | Data bus |
11 | DB4 | Data bus |
12 | DB5 | Data bus |
13 | DB6 | Data bus |
14 | DB7 | Data bus |
15 | DB8 | Data bus (When select 8bits mode, this pin is NC) |
16 | DB9 | Data bus (When select 8bits mode, this pin is NC) |
17 | DB10 | Data bus (When select 8bits mode, this pin is NC) |
18 | DB11 | Data bus (When select 8bits mode, this pin is NC) |
19 | DB12 | Data bus (When select 8bits mode, this pin is NC) |
20 | DB13 | Data bus (When select 8bits mode, this pin is NC) |
21 | DB14 | Data bus (When select 8bits mode, this pin is NC) |
22 | DB15 | Data bus (When select 8bits mode, this pin is NC) |
23 | NC | No connection |
24 | NC | No connection |
25 | CS | Chip select |
26 | RESET | Hardware reset |
27 | DIP ON | Display control H: On \ L:Off |
28 | NC | No connection |
29 | NC | No connection |
30 | NC | No connection |
31 | NC | No connection |
32 | NC | No connection |
33 | VLED- | VLED- for B/L LED inverter (GND) |
34 | VLED- | VLED- for B/L LED inverter (GND) |
35 | VLED+ | VLED+ for B/L LED inverter (+3.3V) |
36 | VLED+ | VLED+ for B/L LED inverter (+3.3V) |
Item | Symbol | Min | Typ | Max | Unit |
---|---|---|---|---|---|
Operating Temperature | TOP | -20 | - | +70 | ℃ |
Storage Temperature | TST | -30 | - | +80 | ℃ |
Operating conditions: (CON3.Pin1=GND, Pin2=VDD)
Item | Symbol | Condition | Min | Typ | Max | Unit |
---|---|---|---|---|---|---|
Supply Voltage For LCM | VDD | - | 3.0 | 3.1 | 3.3 | V |
Supply Current For LCM | IDD | - | - | 50 | 75 | mA |
Backlight driving conditions (CON3.Pin33,34=VLED-, Pin35,36=VLED+)
Parameter | Symbol | Min. | Typ. | Max. | Unit |
---|---|---|---|---|---|
Operation Current For LED Driver | VLED+=3.3V | 200 | - | 350 | mA |
Power Consumption | VLED+=3.3V | 660 | - | 1155 | mW |
Supply Voltage For LED Driver | VLED+ | 3.3 | - | 5 | V |
LED Life Time | - | 50,000 | - | Hr |