5 inch IPS, MIPI TFT LCD Display Module (PCAP) - RF3500D-AYW-MNG1
5 inch IPS, MIPI TFT LCD Display Module (PCAP) - RF3500D-AYW-MNG1
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
Item Dimension Unit
Size 5 inch
Dot Matrix (Resolution) 720 × 3(RGB) × 1280 dots
Module Dimension 73.3(W) × 127.6(H) × 3.45 mm
Outline Dimension 66.10 × 120.40 mm
View Area 63.1(W) × 111.4(H) mm
Active Area 62.1(W) × 110.4(H) mm
Dot Pitch 0.08625(W) × 0.08625(H) mm
LCD Type TFT, Normally Black, Transmissive
View Direction IPS
Viewing Angle 80/80/80/80
Aspect Ratio 16:9
Backlight Type LED, Normally White
Control-Board No
Built-in Controller No
TFT Driver IC ILI9881C or Equivalent
PCAP FW Version 0x5F
PCAP IC GT928
Interface MIPI DSI
Touch Panel Projected Capacitive Touch Panel, PCAP
Detect Points 10 Finger
Surface Glare
Brightness 250 cd/㎡
Frame Through Hole No
Operating Temperature -20~+70 °C
Storage Temperature -30~+80 °C
TFT Series Standard TFT LCD, IPS TFT LCD

LCM PIN Definition

Pin Symbol Function
1 NC No connection
2 NC No connection
3 NC No connection
4 NC No connection
5 NC No connection
6 NC No connection
7 NC No connection
8 NC No connection
9 NC No connection
10-11 VCI Power supply for analog circuits. Connect to an external power supply of 2.5V to 3.6V
12-13 NC No connection
14 RESET The external reset input
Initializes the chip with a low input. Be sure to execute a power-on reset after supplying power.
Fix to VDDI level when not in use.
15 TE  Tearing effect output pin.
Leave the pin open when not in use.
16 NC No connection
17-18 GND Power ground
19-20 IOVCC Power supply for analog circuits. Connect to an external power supply of 1.65V to 3.6V
21 GND Power ground
22 D3P MIPI DSI differential data pair. (Data lane 3)
23 D3N
24 GND Power ground
25 D2P MIPI DSI differential data pair. (Data lane 2)
26 D2N
27 GND Power ground
28 CLKP MIPI DSI differential clock pair
29 CLKN
30 GND Power ground
31 D1P MIPI DSI differential data pair. (Data lane 1)
32 D1N
33 GND Power ground
34 D0P MIPI DSI differential data pair. (Data lane 0)
35 D0N
36-37 GND Power ground
38 LED+ Power for LED backlight anode
39 LED1- Power for LED1 backlight cathode
40 LED2- Power for LED2 backlight cathode

 

PCAP PIN Definition

Pin Symbol Function
1 SDA I2C data input and output
2 SCL I2C clock input
3 RST External Reset, Low is active
4 INT External interrupt to the host
5 VDD Power Supply : +3.3V
6 GND Ground for analog circuit

5 inch IPS, MIPI TFT LCD Display Module (PCAP) - RF3500D-AYW-MNG1

Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 +70
Storage Temperature TST -30 +80

Typical Operation Conditions

Item Symbol Values Unit
Min Typ Max
Power supply for analog circuit VCI 2.5 3.3 3.6 V
Power supply for logic circuit IOVCC 1.65 1.8 3.6 V
Supply Voltage For Touch Logic VDDT 2.8 - 3.3 V
Current for Driver IDD - 44 - mA

 

Backlight Driving Conditions

Parameter Symbol Min Typ Max Unit
LED current ILED - 40 - mA
LED voltage VLED+ 19.6 - 23.8 V
LED Life Time   30,000 - - Hr
Top