128x64 OLED 顯示器, 128x64 OLED 模組

項目	規格內容	單位
結構	COG
對角線尺寸	0.96	吋
點陣/解析度	128 × 64	dots
模組尺寸	26.7 × 19.26 × 1.26	mm
可視區域(VA)	23.938 × 12.058	mm
有效區域(AA)	21.738 × 10.858	mm
點(像素)大小	0.148 × 0.148	mm
點(像素)間距	0.17 × 0.17	mm
發光色	OLED, 白色 / 黃色 / 藍色
顯示模式	被動矩陣 (Passive Matrix)
IC	SSD1306
介面	6800, 8080, SPI, I2C
電源電壓	3V
驅動方式(Duty)	1/64 duty
工作溫度	-40~+80	°C
儲存溫度	-40~+85	°C
偏光片類型(Polarizer Type)	可選偏光鏡
可選FPC	是
類型	繪圖型OLED顯示器

No.

符號

功能說明

N.C. (GND)

Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

C2N

Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.

C2P

C1P

C1N

VBAT

Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.

VSS

Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.

VDD

Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.

BS0

Communicating Protocol Select
These pins are MCU interface selection input. See the
following table:

	BS0	BS1	BS2
I2C	0	1	0
3-wire SPI	1	0	0
4-wire SPI	0	0	0
8-bit 68XX Parallel	0	0	1
8-bit 80XX Parallel	0	1	1

BS1

BS2

CS#

Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.

RES#

Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.

D/C#

Data/Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data.
When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams.
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection.

R/W#

Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.

E/RD#

Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.

18~25

D0~D7

Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.

IREF

Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.

VCOMH

Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.

VCC

Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

VLSS

Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.

NC
(GND)

Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

REX012864D (Hotbar FPC)

128x64 OLED 顯示器, 128x64 OLED 模組 0.96吋 (Hotbar FPC) - REX012864D

REX012864D (ZIF FPC)

128x64 OLED 顯示器, 128x64 OLED 模組 0.96吋 (ZIF FPC) - REX012864D

參數	符號	最小值	最大值	單位
邏輯電源電壓	VDD	0	4.0	V
顯示電源電壓	VCC	0	15.0	V
工作溫度	TOP	-40	+80	°C
儲存溫度	TSTG	-40	+85	°C

項目	符號	條件	最小值	典型值	最大值	單位
邏輯電源電壓	VDD	－	2.8	3.0	3.3	V
顯示電源電壓	VCC	－	11.5	12.0	12.5	V
輸入高電壓	VIH	－	0.8×VDD	－	VDDIO	V
輸入低電壓	VIL	－	0	－	0.2×VDD	V
輸出高電壓	VOH	－	0.9×VDD	－	VDDIO	V
輸出低電壓	VOL	－	0	－	0.1×VDD	V
VCC工作電流 (50% display ON)	ICC	Vcc =12V	－	16	20	mA

可選FPC

FPC 長度	PIN	Pitch	ZIF / HOTBAR FPC	介面	FPC No.	鍵立日期
22	30	0.7	HOTBAR	6800,8080,SPI,I2C	FPC2070003001XXXXX08	20170808
41.1	30	0.5	ZIF	6800,8080,SPI,I2C	FPC2050003011XXXXX28	20180604
13.1	30	0.5	ZIF	6800,8080,SPI,I2C	FPC2050003011XXXXX34	20200221