2.7 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC;可選鐵框;可選FPC）- REX012864K
2.7 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC;可選鐵框;可選FPC）- REX012864K
2.7 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC;可選鐵框;可選FPC）- REX012864K
2.7 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC;可選鐵框;可選FPC）- REX012864K

2.7 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC;可選鐵框;可選FPC）

Model No. REX012864K

REX012864K 是一款 2.7 吋 128×64 COG 繪圖型 OLED 顯示器模組，具備可選鐵框及可選 FPC 選擇，包括 ZIF 與 Hotbar FPC。此模組可輸出清晰的單色畫面，發光顏色有白色、黃色、綠色與天藍色。其纖薄設計（73.0 × 41.86 × 2.11 mm）非常適合手持裝置、控制面板及工業設備使用。

REX012864K 以高可靠性為設計核心，能在 -40°C 至 +80°C 的寬溫範圍下運作，並支援最高 +85°C 的儲存溫度。其高效電壓範圍（2.8–3.3V 邏輯電壓，12–14V 顯示電壓）確保穩定且長久的效能。這款多功能的 2.7 吋 OLED 顯示器模組，是各種嵌入式應用的耐用解決方案。

如需 REX012864K 或其他 2.7 吋 OLED 顯示器模組的技術支援或產品報價，歡迎聯繫我們的銷售團隊！

資料來源參考：REX012864KYAP3N00000

產品詢問 規格書下載 回上頁 上一個產品 下一個產品
  • 一般規格
  • Pin 功能定義
  • 規格圖
  • 最大絕對額定值
  • 電氣特性
  • 選項
項目 規格內容 單位
結構 COG; 可選鐵框
對角線尺寸 2.7 吋
點陣/解析度 128 × 64 dots
模組尺寸 73.0 × 41.86 × 2.11 mm
可視區域(VA) 63.41 × 32.69 mm
有效區域(AA) 61.41 × 30.69 mm
點(像素)大小 0.45 × 0.45 mm
點(像素)間距 0.48 × 0.48 mm
發光色 OLED, 白色 / 黃色 / 綠色 / 天空藍
顯示模式 被動矩陣 (Passive Matrix)
IC SSD1309
介面 8080 / 6800 / SPI / I2C
電源電壓 3V
驅動方式(Duty) 1/64 duty
工作溫度 -40~+80 °C
儲存溫度 -40~+85 °C
偏光片類型(Polarizer Type) 可選偏光鏡
可選FPC 是
類型 繪圖型OLED顯示器
Pin No. 符號 功能說明
1 NC(GND) No Connection
2 VSS Ground.
3~10 NC No connection
11 VDD Power supply pin for core logic operation
12 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select.
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68XX Parallel 0 1
8-bit 80XX Parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD 
13 BS2
14 NC No connection
15 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS.
18 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
19 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
20~27 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout,SDAin in application and D0 is the serial clock input, SCL.
28 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
29 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
30 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
31 NC(GND) No connection

2.7 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC;可選鐵框;可選FPC）- REX012864K 規格圖

參數 符號 最小值 最大值 單位
邏輯電源電壓 VDD -0.3 4 V
顯示器電源電壓 VCC 0 15 V
工作溫度 TOP -40 +80 °C
儲存溫度 TSTG -40 +85 °C
項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VDD - 2.8 3.0 3.3 V
顯示器電源電壓 VCC - 12 13 14 V
輸入高準位 VIH - 0.8×VDD - - V
輸入低準位 VIL - - - 0.2×VDD V
輸出高準位 VOH - 0.9×VDD - - V
輸出低準位 VOL - - - 0.1×VDD V
50%顯示畫面耗電流 VCC =13.0V - 22 33 mA

可選鐵框

圖示 材質 FR No. 詳細規格圖 建立日期
REH012864K SUS-304 FFL60128640A221XXX00 檢視 20120131

可選FPC

圖示 FPC 長度 PIN pitch ZIF / HOTBAR FPC 介面 FPC No. 建立日期
 FPC2050003111XXXXX01_REX012864K 36 31 0.5 ZIF 6800, 8080, SPI, I2C FPC2050003111XXXXX01 20140923
 FPC2050002211XXXXX03_REX012864K 69.85 22 0.5 ZIF 6800, 8080, SPI, I2C FPC2050002211XXXXX03 20161207
 FPC2050002411XXXXX11_REX012864K 105.57 30 0.5 ZIF 6800, 8080, SPI, I2C FPC2050003011XXXXX11 20170406
 FPC2050003011XXXXX11_REX012864K 42 24 0.5 ZIF 6800, 8080, SPI, I2C FPC2050002411XXXXX11 20191218

相關產品

Top