2.7吋 128x64 COG OLED顯示器搭載鐵框+PCB - REP012864Q
2.7吋 128x64 COG OLED顯示器搭載鐵框+PCB - REP012864Q
2.7吋 128x64 COG OLED顯示器搭載鐵框+PCB - REP012864Q
2.7吋 128x64 COG OLED顯示器搭載鐵框+PCB - REP012864Q
2.7吋 128x64 COG OLED顯示器搭載鐵框+PCB - REP012864Q
2.7吋 128x64 COG OLED顯示器搭載鐵框+PCB - REP012864Q
2.7吋 128x64 COG OLED顯示器搭載鐵框+PCB - REP012864Q
2.7吋 128x64 COG OLED顯示器搭載鐵框+PCB - REP012864Q

2.7吋 128x64 COG OLED顯示器搭載鐵框+PCB

Model No. REP012864Q

REP012864Q 是一款 2.7 吋單色繪圖型COG OLED 模組，顯示器解析度為128x64像素。模組尺寸為 82.0×47.5 mm，有效顯示區域尺寸為 61.41×30.69 mm。此款顯示器內建 SSD1309 IC，可支援 6800、8080 串列介面和 SPI 並列介面。此模組附加有鐵框讓使用者節省自行開發PCB 的時間。同時，具有四個螺絲孔的附加框架可讓使用者快速安裝。

如果需要 CTP 觸控功能，請考慮此系列中的 REP012864Q-CTP 系列模組。

模組邏輯供電電壓範圍為 2.8V 至 3.3V，典型值為 3V。可用的發光顏色包括白色、黃色、天藍色和綠色。模組工作溫度為-40℃至+80℃；儲存溫度為-40℃至+85℃。

規格來源：REP012864QSAP3N00000

產品詢問 規格書下載 回上頁 上一個產品 下一個產品
  • 一般規格
  • Pin功能定義
  • 規格圖
  • 最大絕對額定值
  • 電氣特性
項目 規格內容 單位
結構 COG + FR + PCB
對角線尺寸 2.7 吋
點陣/解析度 128 × 64 dots
模組尺寸 82.0 × 47.5 × 7 mm
可視區域(VA) 64.41 × 33.69 mm
有效區域(AA) 61.41 × 30.69 mm
點(像素)大小 0.45 × 0.45 mm
點(像素)間距 0.48 × 0.48 mm
發光色 白色 / 黃色 / 天藍色 / 綠色
顯示模式 被動矩陣 (Passive Matrix)
IC SSD1309
介面 6800,8080,4-Wire SPI,I2C
電源電壓 3V
驅動方式(Duty) 1/64 duty
工作溫度 -40~+80 °C
儲存溫度 -40~+85 °C
類型 繪圖型OLED顯示器
No. 符號 功能
1 VSS Ground.
2 VDD Power supply pin for core logic operation
3 NC No connection
4 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
5 R/W#
(WR#)		 This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
6 E(/RD#) This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
7-14 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
15 NC No connection
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68xx Parallel 0 1
8-bit 80xx Parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 NC No connection
22 NC No connection
23 NC No connection
24 NC No connection

2.7吋 128x64 COG OLED顯示器搭載鐵框+PCB - REP012864Q

參數 符號 最小值 最大值  單位
邏輯電源電壓 VDD -0.3 4 V
工作溫度 TOP -40 +80 °C
儲存溫度 TSTG -40 +85 °C

DC 電氣特性

項目 符號 條件 最小值 典型值 最大值  單位
邏輯電源電壓 VDD － 2.8 3.0 3.3 V
High Level Input VIH － 0.8×VDD － － V
Low Level Input VIL － － － 0.2×VDD V
High Level Output VOH － 0.9×VDD － － V
Low Level Output VOL － － － 0.1×VDD V
50% Check Board operating Current VDD =3V － 175 350 mA

相關產品

Top