RET025664A - Raystar

Spécification
Fonction des broches d’interface
Dessin de contour
Valeurs nominales maximales absolues
Electrical Characteristics

Article	Dimensions	Unité
Structure	COF
Taille (diagonale)	2.8	pouces
Résolution matricielle	256 × 64	points
Dimensions du module	84.0 × 25.8 × 2.15	mm
Surface de visée (VA)	71.104 × 19.264	mm
Aire active (AA)	69.098 × 17.258	mm
Taille de point et de pixel	0.248 × 0.248	mm
Espacement de point et de pixel	0.27 × 0.27	mm
Couleur émise	OLED, Blanc / Jaune
Prise en charge de la gamme de gris	Yes
Mode d’affichage	Matrice passive
IC	SSD1322
Interface	8080, 6800, SPI
Tension d’alimentation	3V
Duty	1/64 cycle de service
Température de fonctionnement	-40~+80	°C
Température de rangement	-40~+85	°C
Type de polariseur	Polariseur optionnel
Type	Affichage OLED graphiques

Pin No.

Symbole

I/O

Description

Power Supply

VCI

Power Supply for Operation
This is a voltage supply pin. It must be connected to external source & always be equal to or higher than VDD & VDDIO.

VDD

Power Supply for Core Logic Circuit
This is a voltage supply pin. It can be supplied externally (within the range of 2.4~2.6V) or regulated internally from VCI. A capacitor should be connected between this pin & VSS under all circumstances.

VDDIO

Power Supply for I/O Pin
This pin is a power supply pin of I/O buffer. It should be connected to VDD or external source. All I/O signal should have VIH reference to VDDIO. When I/O signal pins (BS0~BS1, D0~D7, control signals…) pull high, they should be connected to VDDIO.

VSS

Ground of Logic Circuit
This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground.

3,29

VCC

Power Supply for OLED Panel
These are the most positive voltage supply pin of the chip. They must be connected to external source.

5,28

VLSS

Ground of Analog Circuit
These are the analog ground pins. They should be connected to VSS externally.

Driver

IREF

Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA.

VCOMH

Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A tantalum capacitor should be connected between this pin and VSS.

VSL

Voltage Output Low Level for SEG Signal
This is segment voltage reference pin.
When external VSL is not used, this pin should be left open.
When external VSL is used, this pin should connect with resistor and diode to ground.

Testing Pads

Frame Frequency Triggering Signal
This pin will send out a signal that could be used to identify the driver status. Nothing should be connected to this pin. It should be left open individually.

BS0

Communicating Protocol Select
These pins are MCU interface selection input. See the following table:

	BS0	BS1
3-wire SPI	1	0
4-wire SPI	0	0
8-bit 68XX Parallel	1	1
8-bit 80XX Parallel	0	1

BS1

RES#

Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.

CS#

Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.

D/C#

Data/Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data.
When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams.

E/RD#

Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.

R/W#

Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.

6~13

D7~D0

I/O

Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
Unused pins must be connected to VSS except for D2 in serial mode

Reserve

N.C.

Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.

1,30

N.C. (GND)

Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

2,8 po OLED d'affichage graphique, SSD1322 OLED afficheur , 256x64, COF, 8080/6800/SPI - RET025664A

Paramètre	Symbole	Min	Max	Unité
Supply Voltage for Logic	VDD	-0.5	2.75	V
Low voltage power supply	VCI	-0.3	4.0	V
Power supply for I/O pins	VDDIO	-0.5	VCI	V
Supply Voltage for Display	VCC	-0.5	20.0	V
Température de fonctionnement	TOP	-40	+80	°C
Température de stockage	TSTG	-40	+85	°C

DC Electrical Characteristics

Élément	Symbole	Conditions	Min	Typ	Max	Unité
Supply Voltage for Logic	VCI	－	2.8	3.0	3.3	V
Supply Voltage for Display	VCC	－	14	14.5	15	V
High Level Input	VIH	－	0.8×VDDIO	－	VDDIO	V
Low Level Input	VIL	－	0	－	0.2×VDDIO	V
High Level Output	VOH	－	0.9×VDDIO	－	VDDIO	V
Low Level Output	VOL	－	0	－	0.1×VDDIO	V
50% Check Board operating Current		VCC =14.5V	－	30	32	mA