Afficheur OLED I2C de 0,96 po, OLED graphique I2C, 128x64

Afficheur OLED I2C de 0,96 po, OLED graphique I2C, 128x64, SH1106, 6800/8080/SPI/I2C

Model No. REX012864C

Le REX012864C est un module COG d’ afficheur OLED I2C de 0,96 pouces. La dimension du module est de 26,7×19,26 mm (diagonale de 0,96 pouces) et l’aire active est de 21,74×10,86 mm. Cet afficheur OLED présente un rapport de contraste élevé de 10000:1 et la résolution est de 128×64 points. Il est doté d’un circuit intégré de pilote SH1106 qui prend en charge les interfaces I2C, 6800, 8080 et 4-wire SPI.

La tension d'alimentation de ce 0.96 po OLED I2C est entre 2,8 V et 3,3 V, et la valeur normale est de 3,0 V. La plage de températures de fonctionnement est de -40°C à +80°C; la température de stockage couvre une plage de -40°C à +85℃.

Data source ref: REX012864CWAP3N00001

Ajouter à demande / Demo Code

Téléchargement PDF

Retour

Spécification
Fonction des broches d’interfacePin Function
Dessin de contour
Valeurs absolues maximales
Paramètres électriques
Options

Article	Dimensions	Unité
Structure	COG
Taille (diagonale)	0.96	pouces
Résolution matricielle	128 × 64	points
Dimensions du module	26.70 × 19.26 × 1.26	mm
Surface de visée (VA)	23.34 × 11.46	mm
Aire active (AA)	21.74 × 10.86	mm
Taille de point et de pixel	0.148 × 0.148	mm
Espacement de point et de pixel	0.170 × 0.170	mm
Couleur émise	OLED, Blanc / Jaune
Mode d’affichage	Matrice passive
IC	SH1106
Interface	6800, 8080, 4-wire SPI, I2C
Tension d’alimentation	3V
Duty	1/64 cycle de service
Température de fonctionnement	-40~+80	°C
Température de rangement	-40~+85	°C
Type de polariseur	Polariseur optionnel
Options FPC	Yes
Type	Affichage OLED graphiques

No.

Symbole

Fonction

No connection

C1N

Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.

C1P

C2P

Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.

C2N

VDD2

3.0 – 4.7V power supply pad for Power supply for charge pump circuit.
This pin should be disconnected when VPP is supplied externally

No connection

VSS

Ground.

VDD1

Power supply input: 1.65 - 3.5V

No connection

IM1

These are the MPU interface mode select pads.

	8080	1²C	6800	4-wire SPI
IM1	1	1	0	0
IM2	1	0	1	0

IM2

CSB

This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.

RESB

This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.

This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.

WRB

This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.

RDB

This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.

This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.

IREF

This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.

VCOMH

This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.

VPP

OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.

No connection

REX012864C Afficheur OLED avec Hotbar FPC

Afficheur OLED I2C de 0,96 po, OLED graphique I2C, 128x64, SH1106, 6800/8080/SPI/I2C - REX012864C

REX012864C Afficheur OLED avec ZIF FPC

Afficheur OLED I2C de 0,96 po, OLED graphique I2C, 128x64, SH1106, 6800/8080/SPI/I2C - REX012864C

Paramètre	Symbole	Min	Max	Unité
Tension d’alimentation pour le circuit logique	VDD1	-0.3	3.6	V
Power supply for charge pump circuit	VDD2	-0.3	4.8	V
Tension d’alimentation pour l’affichage	VPP	-0.3	14.5	V
Température de fonctionnement	TOP	-40	+80	°C
Température de rangement	TSTG	-40	+85	°C

DC Paramètres électriques

Élément	Symbole	Condition	Min	Typ	Max	Unité
Tension d’alimentation pour le circuit logique	VDD1	－	2.8	3.0	3.3	V
Power supply for charge pump circuit	VDD2	－	3.5	3.8	4.2	V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC)	Charge Pump VPP	－	7.5	8	8.5	V
Entrée à niveau élevé	VIH	－	0.8xVDD1	－	VDD1	V
Entrée à bas niveau	VIL	－	VSS	－	0.2xVDD1	V
Sortie à niveau élevé	VOH	－	0.8xVDD1	－	VDD1	V
Sortie à bas niveau	VOL	－	VSS	－	0.2xVDD1	V
Operating Current for VDD2 Display 50% ON	IDD2	－	－	10	16	mA