- Allgemeine Spezifikationen
- Schnittstelle Pin-Funktion
- Zeichnung
- Absolute Grenzwerte
- Elektrische Eigenschaften
- Video
| Artikel | Ausmaß | Einheit |
|---|---|---|
| Bauweise | COG | |
| Größe (Diagonale) | 0.69 | Zoll |
| Punktmatrix (Auflösung) | 96 × 16 | Punkte |
| Abmaße der modul | 26.3 × 8.0 × 1.26 | mm |
| Anzeigebereich (VA) | 19.26 × 5.18 | mm |
| Aktiver Bereich (AA) | 17.26 × 3.18 | mm |
| Punktgröße | 0.16 × 0.18 | mm |
| Punktabstand | 0.18 × 0.20 | mm |
| Emittierende Farbe | OLED, Weiß / Gelb | |
| der Anzeigemodus | Passive Matrix | |
| IC | SSD1306 | |
| Schnittstelle | I2C | |
| Stromversorgung | 3V | |
| Duty | 1/16 Duty | |
| Betriebstemperatur | -30~+70 | °C |
| Lagertemperatur | -30~+70 | °C |
| Typ | OLED-Grafikdisplay / Grafikmodul / OLED Anzeige / OLED-Display |
| Pin No. | Symbol | Funktion |
|---|---|---|
| 1 | C2N | C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor. C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor. |
| 2 | C2P | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
| 6 | NC | No connection |
| 7 | VSS | This is a ground pin. |
| 8 | VDD | Power supply pin for core logic operation. |
| 9 | RES# | This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation. |
| 10 | SCL | When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
| 11 | SDA | |
| 12 | IREF | This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA. When internal IREF is used, this pin should be kept NC. |
| 13 | VCOMH | The pin for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
| 14 | VCC | This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
| Parameter | Symbol | Mindestwert | Maximalwert | Einheit |
|---|---|---|---|---|
| Versorgungsspannung für Logik | VDD | 0 | 4 | V |
| Versorgungsspannung für Display | VCC | 0 | 16 | V |
| Charge Pump Regulator Supply Voltage | VBAT | 0 | 5 | V |
| Betriebstemperatur | TOP | -30 | 70 | °C |
| Lagertemperatur | TSTG | -30 | 70 | °C |
| Artikel | Symbol | Bedingung | Mindestwert | typischer Wert | Maximalwert | Einheit |
|---|---|---|---|---|---|---|
| Versorgungsspannung für Logik | VDD | － | 1.65 | 3.0 | 3.3 | V |
| Versorgungsspannung für Display (Supplied Externally) | VCC | － | 6.0 | 7.5 | 8.0 | V |
| Charge Pump Regulator Supply Voltage | VBAT | － | 3.0 | － | 4.2 | V |
| Charge Pump Output Voltage for Display (Generated by Internal DC/DC) | Charge Pump VCC |
－ | 7.0 | 7.5 | － | V |
| Eingang Hochspannung | VIH | － | 0.8×VDD | － | VDD | V |
| Niedrige Eingangsspannung | VIL | － | 0 | － | 0.2×VDD | V |
| Ausgang Hochspannung | VOH | － | 0.9×VDD | － | VDD | V |
| Ausgang niedrige Spannung | VOL | － | 0 | － | 0.1×VDD | V |
| 50% Check Board Operating Current (VCC Supplied Externally) | ICC | － | － | 5 | 10 | mA |
| 50% Check Board Operating Current (VCC Generated by Internal DC/DC) | IBAT | － | 5 | 10 | mA |
REX009616B – Demovideo zum 0,69-Zoll-OLED-Displaymodul
