- Allgemeine Spezifikationen
- Schnittstelle Pin-Funktion
- Zeichnung
- Absolute Grenzwerte
- Elektrische Eigenschaften
- Optional
| Artikel | Ausmaß | Einheit |
|---|---|---|
| Bauweise | COG | |
| Größe (Diagonale) | 0.71 | Zoll |
| Punktmatrix (Auflösung) | 48 × 64 | Punkte |
| Abmaße der modul | 13.90 × 22.0 × 1.26 | mm |
| Anzeigebereich (VA) | 12.14 × 16.30 | mm |
| Aktiver Bereich (AA) | 10.54 × 14.70 | mm |
| Punktgröße | 0.20 × 0.21 | mm |
| Punktabstand | 0.22 × 0.23 | mm |
| Emittierende Farbe | OLED, Weiß / Gelb | |
| der Anzeigemodus | Passive Matrix | |
| IC | SSD1306 | |
| Schnittstelle | I2C | |
| Stromversorgung | 3V | |
| Duty | 1/64 Duty | |
| Betriebstemperatur | -40~+80 | °C |
| Lagertemperatur | -40~+85 | °C |
| Polarizer Type | Polarizer optional | |
| FPC-Optionen | Yes | |
| Typ | OLED-Grafikdisplay / Grafikmodul / OLED Anzeige / OLED-Display |
| No. | Symbol | Funktion |
|---|---|---|
| 1 | C2N | Positive Terminal of the Flying Inverting Capacitorr Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
| 2 | C2P | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
| 6 | NC | No connection. |
| 7 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
| 8 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
| 9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
| 10 | SCL | Host Data Input/Output Bus When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL. |
| 11 | SDA | |
| 12 | IREF | This is segment output current reference pin. When external IREF is used, a resistor should be connected between this pin and Vss to maintain the IREF current at a maximum of 30uA. When internal IREF is used, this pin should be kept NC |
| 13 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
| 14 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
| Parameter | Symbol | Mindestwert | Maximalwert | Einheit |
|---|---|---|---|---|
| Versorgungsspannung für Logik | VDD | 0 | 4.0 | V |
| Versorgungsspannung für Display | VCC | 0 | 15.0 | V |
| Betriebstemperatur | TOP | -40 | +80 | °C |
| Lagertemperatur | TSTG | -40 | +85 | °C |
| Artikel | Symbol | Bedingung | Mindestwert | typischer Wert | Maximalwert | Einheit |
|---|---|---|---|---|---|---|
| Versorgungsspannung für Logik | VDD | － | 2.8 | 3.0 | 3.3 | V |
| Versorgungsspannung für Display | VCC | － | 7.0 | 7.5 | 8.0 | V |
| Eingang Hochspannung | VIH | － | 0.8×VDD | － | VDD | V |
| Niedrige Eingangsspannung | VIL | － | 0 | － | 0.2×VDD | V |
| Ausgang Hochspannung | VOH | － | 0.9×VDD | － | VDD | V |
| Ausgang niedrige Spannung | VOL | － | 0 | － | 0.1×VDD | V |
| 50% Check Board Operating Current | ICC | VCC=7.5V | － | 15.0 | 25.0 | mA |
FPC Optional
| Drawing | FPC Length | PIN | pitch | ZIF / HOTBAR FPC | Interface | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
16.0 | 14 | 0.7 | HOTBAR FPC | I2C | FPC2000701401XXXXX00 | 20160603 |
 |
11.2 | 14 | 0.7 | HOTBAR FPC | I2C | FPC2070001401XXXXX02 | 20180307 |
