REX009664D - Raystar Optronics, Inc.

Modulo Display OLED Grafico COG 0,95 pollici 96×64 (IC SSD1315)

Model No. REX009664D

Il REX009664D è un modulo display OLED a matrice passiva da 0,95 pollici con struttura COG (Chip-on-Glass). Offre una risoluzione di 96×64 punti in un formato compatto di 24,9 × 22,95 × 1,61 mm.

Questo modulo supporta diverse interfacce, tra cui 6800, 8080, SPI a 4 fili e I2C. È gestito dal controller SSD1315 e progettato con un duty cycle 1/64. Il REX009664D è ideale per applicazioni come elettrodomestici intelligenti, dispositivi portatili industriali e apparecchiature mediche.

Supporta un ampio intervallo di temperatura operativa da -40°C a +80°C. La tensione logica (VDD) varia da 2,4V a 3,3V, con un consumo tipico di 6–9 mA al 50% di attivazione dei pixel.

Per assistenza tecnica o preventivi sul REX009664D o su altri moduli OLED da 0,95 pollici, non esitare a contattare il nostro team commerciale.

Fonte dati: REX009664DYPP3N00000

AGGIUNGI ALLA RICHIESTA/Demo Code

SCARICA PDF

Indietro

Specifiche generali
Funzione dei Pin di Interfaccia
Disegno
Valori massimi assoluti
Caratteristiche elettriche

Articolo	Dimensioni	Unità
Struttura	COG
Dimensione (Diagonale)	0.95	pollici
A matrice di punti (Risoluzione)	96 × 64	punti
Dimensione del modulo	24.9 × 22.95 × 1.61	mm
Area di visualizzazione (VA)	21.953 × 15.424	mm
Area attiva (AA)	19.946 × 13.418	mm
Dimensioni del Dot	0.184 × 0.186	mm
Passo del Dot	0.208 × 0.21	mm
Colore di emissione	OLED, Bianco / Giallo
Modalità display	Matrice passiva
IC	SSD1315
Interfaccia	6800 / 8080 / 4-wire SPI / I2C
Alimentatore	3V
Duty	1/64 Duty
Temperatura di lavoro	-40~+80	°C
Temperatura di stock	-40~+85	°C
Polarizer Type	polarizzatore opzionale
Type	Modulo display OLED grafico

Pin No.

Simbolo

Funzione

No connection

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin.

VSS

Ground pin. It must be connected to external ground.

No connection

VDD

Power supply pin for core logic operation.

BS1

MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 are pin select

BS[2:1]	Interface
00	4 line SPI
01	I2C
11	8-bit 8080 parallel
10	8-bit 6800 parallel

Note
(1) 0 is connected to VSS (2) 1 is connected to VDD

BS2

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

RES#

This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.

D/C#

This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection.

R/W#

This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

E/RD#

This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.

IREF

This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin.

VLSS

This is an analog ground pin. It should be connected to VSS externally.

No connection

Modulo Display OLED Grafico COG 0,95 pollici 96×64 (IC SSD1315) - REX009664D Disegno

Parametro	Simbolo	Valore Min	Valore Tipico	Valore Massimo	Unità
Tensione Alimentazione per Logica	VDD	-0.3	－	4.0	V
Tensione Alimentazione per Display	VCC	0	－	18.0	V
Temperatura Lavoro	TOP	-40	－	+80	°C
Temperatura Stock	TSTG	-40	－	+85	°C

Caratteristiche Elettriche DC

Articolo	Simbolo	Condizione	Valore Min	Valore Tipico	Valore Massimo	Unità
Tensione Alimentazione per Logica	VDD	－	1.65	3.0	3.3	V
Tensione Alimentazione per Display	VCC	－	7.5	12.0	12.5	V
Ingresso Alto Livello	VIH	－	0.8×VDD	－	VDD	V
Ingresso Basso Livello	VIL	－	0	－	0.2×VDD	V
Uscita Alto Livello	VOH	Iout = 100uA	0.9×VDD	－	VDD	V
Uscita Basso Livello	VOL	Iout = 100uA	0	－	0.1×VDD	V
Display 50% Pixel on	ICC	－	－	6	9	mA