RET025664A - Raystar

Specifiche generali
Funzione dei Pin di Interfaccia
Disegno
Valori massimi assoluti
Caratteristiche elettriche

Articolo	Dimensioni	Unità
Struttura	COF
Dimensione (Diagonale)	2.8	pollici
A matrice di punti (Risoluzione)	256 × 64	punti
Dimensione del modulo	84.0 × 25.8 × 2.15	mm
Area di visualizzazione (VA)	71.104 × 19.264	mm
Area attiva (AA)	69.098 × 17.258	mm
Dimensioni del Dot	0.248 × 0.248	mm
Passo del Dot	0.27 × 0.27	mm
Colore di emissione	OLED, Bianco / Giallo
Supporto scala di grigi	Yes
Modalità display	Matrice passiva
IC	SSD1322
Interfaccia	8080, 6800, SPI
Alimentatore	3V
Duty	1/64 duty
Temperatura di lavoro	-40~+80	°C
Temperatura di stock	-40~+85	°C
Polarizer Type	polarizzatore opzionale
Type	Modulo display OLED grafico

Pin No.

Simbolo

I/O

Funzione

Power Supply

VCI

Power Supply for Operation
This is a voltage supply pin. It must be connected to external source & always be equal to or higher than VDD & VDDIO.

VDD

Power Supply for Core Logic Circuit
This is a voltage supply pin. It can be supplied externally (within the range of 2.4~2.6V) or regulated internally from VCI. A capacitor should be connected between this pin & VSS under all circumstances.

VDDIO

Power Supply for I/O Pin
This pin is a power supply pin of I/O buffer. It should be connected to VDD or external source. All I/O signal should have VIH reference to VDDIO. When I/O signal pins (BS0~BS1, D0~D7, control signals…) pull high, they should be connected to VDDIO.

VSS

Ground of Logic Circuit
This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground.

3,29

VCC

Power Supply for OLED Panel
These are the most positive voltage supply pin of the chip. They must be connected to external source.

5,28

VLSS

Ground of Analog Circuit
These are the analog ground pins. They should be connected to VSS externally.

Driver

IREF

Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA.

VCOMH

Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A tantalum capacitor should be connected between this pin and VSS.

VSL

Voltage Output Low Level for SEG Signal
This is segment voltage reference pin.
When external VSL is not used, this pin should be left open.
When external VSL is used, this pin should connect with resistor and diode to ground.

Testing Pads

Frame Frequency Triggering Signal
This pin will send out a signal that could be used to identify the driver status. Nothing should be connected to this pin. It should be left open individually.

BS0

Communicating Protocol Select
These pins are MCU interface selection input. See the following table:

	BS0	BS1
3-wire SPI	1	0
4-wire SPI	0	0
8-bit 68XX Parallel	1	1
8-bit 80XX Parallel	0	1

BS1

RES#

Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.

CS#

Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.

D/C#

Data/Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data.
When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams.

E/RD#

Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.

R/W#

Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.

6~13

D7~D0

I/O

Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
Unused pins must be connected to VSS except for D2 in serial mode

Reserve

N.C.

Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.

1,30

N.C. (GND)

Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

Display OLED COF 2,8 pollici 256x64 SSD1322 - RET025664A

Parametro	Simbolo	Valore Min	Valore massimo	Unità
Supply Voltage for Logic	VDD	-0.5	2.75	V
Low voltage power supply	VCI	-0.3	4.0	V
Power supply for I/O pins	VDDIO	-0.5	VCI	V
Supply Voltage for Display	VCC	-0.5	20.0	V
Temperatura di lavoro	TOP	-40	+80	°C
Temperatura di stock	TSTG	-40	+85	°C

DC Electrical Characteristics

Articolo	Simbolo	Condizioni	Valore Min	Valore tipico	Valore massimo	Unità
Supply Voltage for Logic	VCI	－	2.8	3.0	3.3	V
Supply Voltage for Display	VCC	－	14	14.5	15	V
High Level Input	VIH	－	0.8×VDDIO	－	VDDIO	V
Low Level Input	VIL	－	0	－	0.2×VDDIO	V
High Level Output	VOH	－	0.9×VDDIO	－	VDDIO	V
Low Level Output	VOL	－	0	－	0.1×VDDIO	V
50% Check Board operating Current		VCC =14.5V	－	30	32	mA