- 仕様
- ピン配置
- 外形図
- 絶対最大定格
- 電気特性
| 項目 | 仕様 | 単位 |
|---|---|---|
| 構造 | COG | |
| サイズ(対角線) | 2 | インチ |
| ドットマトリックス / 解像度 | 128 × 32 | ドット |
| モジュール寸法 | 59.0 × 18.86 × 1.41 | mm |
| ビューイングエリア(VA) | 52.535 × 12.695 | mm |
| アクティブエリア(AA) | 50.535 ×10.695 | mm |
| ドットサイズ | 0.37 × 0.31 | mm |
| ドットピッチ | 0.395 × 0.335 | mm |
| 表示色 | OLED, 白色 / 黄色 | |
| ディスプレモード | パッシブマトリクス | |
| IC | SSD1315 | |
| インターフェス | 8Bits 6800/ 8080/ SPI/ I2C | |
| 供給電圧 | 3V | |
| Duty | 1/32 duty | |
| 操作温度 | -40~+80 | °C |
| 保存温度 | -40~+85 | °C |
| 偏光板タイプ | 偏光板オプション | |
| タイプ | グラフィック型 OLED モジュール |
| No. | 記号 | 功能 | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | NC | No connection | ||||||||||||
| 2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. When charge pump is enabled, a capacitor should be connected between this pin and VSS. |
||||||||||||
| 3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||||||||
| 4. | IREF | This is segment output current reference pin. When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA. |
||||||||||||
| 5 | D7 | These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||||||
| 6 | D6 | |||||||||||||
| 7 | D5 | |||||||||||||
| 8 | D4 | |||||||||||||
| 9 | D3 | |||||||||||||
| 10 | D2 | |||||||||||||
| 11 | D1 | |||||||||||||
| 12 | D0 | |||||||||||||
| 13 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||||
| 14 | R/W# | This is read / write control input pin connecting to the MCU interface. When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||||
| 15 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. |
||||||||||||
| 16 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation. | ||||||||||||
| 17 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||||||||
| 18 | NC | No connection | ||||||||||||
| 19 | BS2 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select
(1) 0 is connected to VSS (2) 1 is connected to VDD |
||||||||||||
| 20 | BS1 | |||||||||||||
| 21 | VDD | Power supply pin for core logic operation. This is a voltage supply pin. It must be connected to external source. |
||||||||||||
| 22 | NC | No connection | ||||||||||||
| 23 | NC | |||||||||||||
| 24 | NC | |||||||||||||
| 25 | NC | |||||||||||||
| 26 | NC | |||||||||||||
| 27 | NC | |||||||||||||
| 28 | NC | |||||||||||||
| 29 | NC | |||||||||||||
| 30 | VSS | Ground pin. It must be connected to external ground. | ||||||||||||
| 31 | NC | No connection |
Unless otherwise specified, VSS= 0V ( Ta = 25°C)
| パラメーター | 記号 | 最小値 | 典型値 | 最大値 | 単位 |
|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | -0.3 | - | 4 | V |
| Supply Voltage for Display | VCC | 0 | - | 18 | V |
| 操作温度 | TOP | -40 | - | +80 | °C |
| 保存温度 | TSTG | -40 | - | +85 | °C |
DC 電気特性
Unless otherwise specified, VSS = 0V , VDD = 2.8 - 3.3V ( Ta = 25°C)
| 項目 | 記号 | 最小値 | 典型値 | 最大値 | 単位 | |
|---|---|---|---|---|---|---|
| Supply Voltage | Logic | VDD | 2.8 | 3.0 | 3.3 | V |
| Operating | VCC | 7.5 | 8.0 | 8.5 | V | |
| Input Voltage | High Voltage | VIH | 0.8 x VDD | - | VDD | V |
| Low Voltage | VIL | 0 | - | 0.2 x VDD | V | |
| Output Voltage | High Voltage | VOH | 0.9x VDD | - | VDD | V |
| Low Voltage | VOL | 0 | - | 0.1 x VDD | V | |
| 記号 | パラメーター | 最小値 | 典型値 | 最大値 | 単位 | 条件 |
|---|---|---|---|---|---|---|
| ICC | VCC Supply Current | - | 11 | 22 | mA | VDD=3V , VCC=8.0, Display 50% ON |
