- 仕様
- ピン配置
- 外形図
- 絶対最大定格
- 電気特性
- 影片
| 項目 | 仕様 | 単位 |
|---|---|---|
| 構造 | COG | |
| サイズ(対角線) | 2.7 | インチ |
| ドットマトリックス / 解像度 | 128 × 64 | ドット |
| モジュール寸法 | 73.0 x 41.86 x 2.01 | mm |
| ビューイングエリア(VA) | 63.41 × 32.69 | mm |
| アクティブエリア(AA) | 61.41 x 30.69 | mm |
| ドットサイズ | 0.45 x 0.45 | mm |
| ドットピッチ | 0.48 x 0.48 | mm |
| 表示色 | OLED, 白色 / 黄色 | |
| ディスプレモード | Passive Matrix | |
| IC | CH1116 | |
| インターフェス | 6800,8080,4線式 SPI,I2C | |
| 供給電圧 | 3V | |
| Duty | 1/64 duty | |
| 操作温度 | -40~+80 | °C |
| 保存温度 | -40~+85 | °C |
| タイプ | グラフィック型 OLED モジュール |
| No. | 記号 | 功能 | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | NC(VSS) | No connection | |||||||||||||||
| 2 | VPP | OLED panel power supply. It could be supplied externally. A capacitor should be connected between this pad and VSS. |
|||||||||||||||
| 3 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
|||||||||||||||
| 4 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA. | |||||||||||||||
| 5~12 | D7~D0 | This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus. When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance. When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance. |
|||||||||||||||
| 13 | E/RD# | This is a MPU interface input pad. When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD# signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”. When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU. When RD# = “H”: Enable. When RD# = “L”: Disable. |
|||||||||||||||
| 14 | WR# (R/W#) |
This is a MPU interface input pad. When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR# signal. The signals on the data bus are latched at the rising edge of the WR# signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When R/W#= “H”: Read. When R/W#= “L”: Write. |
|||||||||||||||
| 15 | A0 | This is the Data/Command control pad that determines whether the data bits are data or a command. A0 = “H”: the inputs at D0 to D7 are treated as display data. A0 = “L”: the inputs at D0 to D7 are transferred to the command registers. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
|||||||||||||||
| 16 | RES# | This is a reset signal input pad. When RES# is set to “L”, the settings are initialized. The reset operation is performed by the RES# signal level. | |||||||||||||||
| 17 | CS# | This pad is the chip select input. When CS# = “L”, then the chip select becomes active, and data/command I/O is enabled. | |||||||||||||||
| 18 | NC | No connection | |||||||||||||||
| 19 | IM2 | These are the MPU interface mode select pads.
(1) 0 is connected to VSS (2) 1 is connected to VDD1 |
|||||||||||||||
| 20 | IM1 | ||||||||||||||||
| 21 | VDD1 | Power supply input | |||||||||||||||
| 22~28 | NC | No connection | |||||||||||||||
| 29 | VSS | Ground. | |||||||||||||||
| 30 | NC(VSS) | No connection |
| パラメーター | 記号 | 最小値 | 最大値 | 単位 |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | -0.3 | 3.6 | V |
| Supply Voltage for Display | VCC | 0 | 14.5 | V |
| Operating Temperature | TOP | -40 | +80 | °C |
| Storage Temperature | TSTG | -40 | +85 | °C |
DC 電気特性
| 項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD1 | － | 1.65 | 3.0 | 3.3 | V |
| Supply Voltage for Display | VPP | － | 6.4 | 13.0 | 13.5 | V |
| High Level Input | VIH | － | 0.8×VDD1 | － | VDD1 | V |
| Low Level Input | VIL | － | VSS | － | 0.2×VDD1 | V |
| High Level Output | VOH | － | 0.8×VDD1 | － | VDD1 | V |
| Low Level Output | VOL | － | VSS | － | 0.2×VDD1 | V |
| Display 50% Pixel on | IPP | VPP =13V | － | 15 | 30 | mA |
