- 仕様
- ピン配置
- 外形図
- 絶対最大定格
- 電気特性
- オプション
| 項目 | 仕様 | 単位 |
|---|---|---|
| 構造 | COG | |
| サイズ(対角線) | 0.91 | インチ |
| ドットマトリックス / 解像度 | 128 × 32 | ドット |
| モジュール寸法 | 30.0 × 11.5 × 1.26 | mm |
| ビューイングエリア(VA) | 24.384 × 7.584 | mm |
| アクティブエリア(AA) | 22.384 × 5.584 | mm |
| ドットサイズ | 0.152 × 0.152 | mm |
| ドットピッチ | 0.175 × 0.175 | mm |
| 表示色 | OLED, 白色 / 黄色 / スカイブルー | |
| ディスプレモード | パッシブマトリクス | |
| IC | SSD1306 | |
| インターフェス | 4線式 SPI | |
| 供給電圧 | 3V | |
| Duty | 1/32 duty | |
| 操作温度 | -40~+80 | °C |
| 保存温度 | -40~+85 | °C |
| FPC オプション | あり | |
| タイプ | グラフィック型 OLED モジュール |
| Pin No. | 記号 | 功能 |
|---|---|---|
| 1 | C2P | Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
| 2 | C2N | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
| 6 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
| 7 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
| 8 | CS# | Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. |
| 9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
| 10 | D/C# | Data/Command Control This pin is Data/Command control pin.. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. |
| 11 | SCLK | When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
| 12 | SDIN | |
| 13 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA. |
| 14 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
| 15 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
| パラメーター | 記号 | 最小値 | 最大値 | 単位 |
|---|---|---|---|---|
| ロジック電源電圧 | VDD | 0 | 4.0 | V |
| ディスプレイ電源電圧 | VCC | 0 | 16.0 | V |
| 操作温度 | TOP | -40 | +80 | °C |
| 保存温度 | TSTG | -40 | +85 | °C |
| 項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
|---|---|---|---|---|---|---|
| ロジック電源電圧 | VDD | － | 2.8 | 3.0 | 3.3 | V |
| ディスプレイ電源電圧（Supplied Externally） | VCC | － | 7 | 7.25 | 8 | V |
| チャージポンプレギュレータ電源電圧 | VBAT | － | 3.0 | － | 4.2 | V |
| ディスプレイ用チャージポンプ出力電圧（Generated by Internal DC/DC） | チャージポンプ VCC |
－ | 7.0 | 7.5 | - | V |
| 入力電圧（High） | VIH | － | 0.8×VDD | － | VDD | V |
| 入力電圧（Low） | VIL | － | 0 | － | 0.2×VDD | V |
| 出力電圧（High） | VOH | － | 0.9×VDD | － | VDD | V |
| 出力電圧（Low） | VOL | － | 0 | － | 0.1×VDD | V |
| VCC 動作電流（VCC Supplied Externally） | ICC | VCC =7.25V | － | 7 | 11 | mA |
| ディスプレイ50%ピクセルオン（VCC Generated by Internal DC/DC） | IBAT | － | － | 15 | 25 | mA |
FPC オプション
| 外形図 | FPC Length | PIN | pitch | ZIF / HOTBAR FPC | インターフェス | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
17.06 | 15 | 0.65 | HOTBAR FPC | SPI | FPC2065001501XXXXX00 | 20140827 |
 |
40.76 | 15 | 0.5 | ZIF FPC | SPI | FPC2050001511XXXXX02 | 20150421 |
 |
11.26 | 14 | 0.62 | HOTBAR FPC | I2C | FPC2062001401XXXXX02 | 20160106 |
