- 仕様
- ピン配置
- 外形図
- 絶対最大定格
- 電気特性
- オプション
| 項目 | 仕様 | 単位 |
|---|---|---|
| 構造 | COG | |
| サイズ(対角線) | 0.68 | インチ |
| ドットマトリックス / 解像度 | 96 × 32 | ドット |
| モジュール寸法 | 19.80 × 12.32 × 1.21 | mm |
| ビューイングエリア(VA) | 17.298 × 6.418 | mm |
| アクティブエリア(AA) | 16.298 × 5.418 | mm |
| ドットサイズ | 0.148 × 0.148 | mm |
| ドットピッチ | 0.17 × 0.17 | mm |
| 表示色 | OLED, 白色 / 黄色 | |
| ディスプレモード | パッシブマトリクス | |
| IC | SSD1315 | |
| インターフェス | 8-bits 6800, 8-bits 8080, 4-line SPI, I2C | |
| 供給電圧 | 3V | |
| Duty | 1/32 Duty | |
| 操作温度 | -40~+80 | °C |
| 保存温度 | -40~+85 | °C |
| FPC オプション | あり | |
| タイプ | グラフィック型 OLED モジュール |
| Pin No. | 記号 | 功能 | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
| 2 | NC | No connection | ||||||||||
| 3 | VDD | Power supply pin for core logic operation. | ||||||||||
| 4~8 | NC | No connection | ||||||||||
| 9 | VDD | Power supply pin for core logic operation. | ||||||||||
| 10 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 are pin select
(1) 0 is connected to VSS (2) 1 is connected to VDD |
||||||||||
| 11 | BS2 | |||||||||||
| 12 | NC | No connection | ||||||||||
| 13 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||||||
| 14 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation. | ||||||||||
| 15 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
||||||||||
| 16 | W/R# | This is read / write control input pin connecting to the MCU interface. When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||
| 17 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
REX009632C with ZIF FPC
REX009632C with Hotbar FPC
| パラメーター | 記号 | 最小値 | 典型値 | 最大値 | 単位 |
|---|---|---|---|---|---|
| ロジック電源電圧 | VDD | -0.3 | - | 4 | V |
| ディスプレイ電源電圧 | VCC | 0 | - | 18 | V |
| 操作温度 | TOP | -40 | - | +80 | °C |
| 保存温度 | TSTG | -40 | - | +85 | °C |
DC 特性
| 項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
|---|---|---|---|---|---|---|
| ロジック電源電圧 | VDD | － | 1.65 | 3.0 | 3.3 | V |
| ディスプレイ電源電圧 | VCC | － | 7.5 | 12.0 | 12.5 | V |
| 高レベル入力 | VIH | － | 0.8×VDD | － | VDD | V |
| 低レベル入力 | VIL | － | 0 | － | 0.2×VDD | V |
| 高レベル出力 | VOH | Iout = 100uA | 0.9×VDD | － | VDD | V |
| 低レベル出力 | VOL | Iout = 100uA | 0 | － | 0.1×VDD | V |
| ディスプレイ50%ピクセルオン | ICC | VCC=12V | － | 5.0 | 7.5 | mA |
FPC オプション
| 外形図 | FPC Length | PIN | pitch | ZIF / HOTBAR FPC | インターフェス | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
30 | 28 | 0.5 | ZIF FPC | 6800, 8080,4-Wire SPI, I2C | FPC2050002811XXXXX01 | 20180131 |
 |
8.479 | 25 | 0.65 | HOTBAR FPC | 6800, 8080,4-Wire SPI, I2C | FPC2065002501XXXXX00 | 20190906 |
