- 仕様
- ピン配置
- 外形図
- 絶対最大定格
- 電気特性
| 項目 | 仕様 | 単位 |
|---|---|---|
| 構造 | COG | |
| サイズ(対角線) | 2.55 | インチ |
| ドットマトリックス / 解像度 | 206 × 36 | ドット |
| モジュール寸法 | 70.77 × 15.14 × 2.01 | mm |
| ビューイングエリア(VA) | 64.84 × 12.14 | mm |
| アクティブエリア(AA) | 63.84 × 11.14 | mm |
| ドットサイズ | 0.29 × 0.29 | mm |
| ドットピッチ | 0.31 × 0.31 | mm |
| 表示色 | OLED, 白色 | |
| グレースケールをサポートする | あり | |
| ディスプレモード | パッシブマトリクス | |
| グレースケール | 4-bit | |
| IC | SSD1362 | |
| インターフェス | 3-Wire SPI, 4-Wire SPI, I2C | |
| 供給電圧 | 3V | |
| Duty | 1/36 Duty | |
| 操作温度 | -40~+80 | °C |
| 保存温度 | -40~+85 | °C |
| タイプ | グラフィック型 OLED モジュール |
| No. | 記号 | 功能 | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 1 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||
| 2 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||||
| 3 | VP | This pin is the segment pre-charge voltage reference pin. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||||
| 4 | VSL | This is a reserved pin. It should be connected to VLSS externally. | ||||||||
| 5 | VLSS | Analog system ground pin. It must be connected to external ground. | ||||||||
| 6 | VDD | VDD can be supplied externally (within the range of 1.65V to 2.6V) or regulated internally from VCI when VCI is >2.6V.A capacitor should be connected between VDD and VSS under all circumstances. | ||||||||
| 7 | VCI | Low voltage power supply. VCI must always be equal to or higher than VDD and VDDIO. |
||||||||
| 8 | VDDIO | Power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. | ||||||||
| 9 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled Low (active Low).In I2C mode, this pin must be connected to VSS. |
||||||||
| 10 | RES# | This pin is reset signal input. When the pin is pulled Low, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||
| 11 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data will be interpreted as data. When the pin is pulled LOW, the data will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
||||||||
| 12 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie Low. When serial interface mode is selected,D0 will be the serial clock input: SCLK;D1 will be the serial data input: SID. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||
| 13 | D1 | |||||||||
| 14 | D2 | |||||||||
| 15 | BS0 | MCU bus interface selection pins.
|
||||||||
| 16 | BS1 | |||||||||
| 17 | VSS | Ground pin. | ||||||||
| 18 | IREF | When external IREF is used, a resistor should be connected between this pin and VSS to maintain current of around 18.75uA. When internal IREF is used, this pin should be kept NC. |
||||||||
| 19~20 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. |
| パラメーター | 記号 | 最小値 | 最大値 | 単位 |
|---|---|---|---|---|
| 電源電圧 | VDD | -0.5 | 2.75 | V |
| 電源電圧 | VCI | -0.3 | 5.5 | V |
| 電源電圧 | VDDIO | -0.5 | 5.5 | V |
| 電源電圧 | VCC | 7 | 21 | V |
| 操作温度 | TOP | -40 | +80 | °C |
| 保存温度 | TSTG | -40 | +85 | °C |
DC 電気特性
| 項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
|---|---|---|---|---|---|---|
| Display電源電圧 | VCC | － | 10.0 | 12.0 | 12.5 | V |
| 低電圧電源 | VCI | － | 1.65 | － | 3.5 | V |
| 入力/出力ピンの電源電圧 | VDDIO | － | 1.65 | － | VCI | V |
| ロジック電源電圧 | VDD | － | 1.65 | － | 2.6 | V |
| High Level Input | VIH | － | 0.8×VDDIO | － | － | V |
| 低レベル入力 | VIL | － | － | － | 0.2×VDDIO | V |
| 高レベル出力 | VOH | － | 0.9×VDDIO | － | － | V |
| 低レベル出力 | VOL | － | － | － | 0.1×VDDIO | V |
| Display 50% Pixel on | ICC | VCC =12V | － | 25 | 35 | mA |
