0.91 inch I2C Graphic OLED Display 128x32 (Thinner Version) - REX012832F
0.91 inch I2C Graphic OLED Display 128x32 (Thinner Version) - REX012832F
0.91 inch I2C Graphic OLED Display 128x32 (Thinner Version) - REX012832F
0.91 inch I2C Graphic OLED Display 128x32 (Thinner Version) - REX012832F
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
Item Dimension Unit
Structure COG
Size 0.91 inch
Dot Matrix (Resolution) 128 × 32 dots
Module Dimension 30.0 × 11.5 × 1.26 mm
View Area 24.384 × 7.584 mm
Active Area 22.384 × 5.584 mm
Dot Size 0.152 × 0.152 mm
Dot Pitch 0.175 × 0.175 mm
Emitting Color OLED, White / Yellow
Display Mode Passive Matrix
Bulit-in Controller SSD1306BZ
Interface I2C
Power Supply 3V
Duty 1/32 duty
Operating Temperature -40-80 °C
Storage Temperature -40-85 °C
Polarizer Type Polarizer optional
Type OLED Graphic Display
No. Symbol Function
1 C2P Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2 C2N
3 C1P
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6 NC No connection
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10 SCL I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin inapplication and D0 is the serial clock input, SCL.
11 SDA
12 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
13 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
14 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

0.91 inch I2C Graphic OLED Display 128x32 - REX012832F - Raystar

Parameter Symbol Min Max Unit
Supply Voltage for Logic VDD 0 4.0 V
Supply Voltage for Display VCC 0 16.0 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C
Item Symbol Condition Min Typ Max Unit
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 7 7.25 8 V
Input High Volt. VIH 0.8×VDD VDDIO V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.9×VDD VDDIO V
Output Low Volt. VOL 0 0.1×VDD V
Operating Current for VCC (VCC Supplied Externally) ICC Vcc =7.25V 7 11 mA
Top