3.12 inch 256x64 OLED Display with Capacitive Touch - RET025664B-CTP
3.12 inch 256x64 OLED Display with Capacitive Touch - RET025664B-CTP
3.12 inch 256x64 OLED Display with Capacitive Touch - RET025664B-CTP
3.12 inch 256x64 OLED Display with Capacitive Touch - RET025664B-CTP
3.12 inch 256x64 OLED Display with Capacitive Touch - RET025664B-CTP

3.12" 256x64 OLED Display with Capacitive Touch

Model No. RET025664B-CTP

RET025664B-CTP is a dot matrix 256x64 COF graphic type OLED display with capacitive touchscreen. The capacitive touch panel has built-in IC FT6336U, supporting 1-point touch. The size of the active area is 3.12” diagonal with module dimension 89.2x29 mm. This 3.12 inches OLED module has built-in IC SSD1322, and boasts high contrast ratio 10,000 : 1. There are many interface options to choose from, including 8-bit 6800 / 8080, 4 line / 3 line SPI, I2C interface.

Logic supply voltage ranges from 2.8V-3.3V, the typical value is 3V. The available emitting colors are white, yellow, green, sky blue and support grayscale.

★Support Grayscale
Data source ref: RET025664BWPP3L00000

Inquiry or Demo Code Datasheet Back Previous Next
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
  • Video
Item Dimension Unit
Structure COF
Size (Diagonal) 3.12 inch
Dot Matrix / Resolution 256 × 64 dots
Module Dimension 89.2 × 29.0 × 3.17 mm
Viewing Area 78.78 × 21.18 mm
Active Area 76.778 × 19.178 mm
Dot / Pixel Size 0.278 × 0.278 mm
Dot / Pixel Pitch 0.300 × 0.300 mm
Emitting Color OLED, White / Yellow / Sky Blue / Green
Support Grayscale Yes
Display Mode Passive Matrix
Gray Scale 4 bits
IC SSD1322 (COF)
Interface 6800,8080,SPI
PCAP IC FT6336U
PCAP Interface I2C
Detect Points 1 Points
Touch Panel Capacitive Touch Panel
Surface Normal Glare
Power Supply 3V
Duty 1/64 Duty
Operating Temperature -20~+70 °C
Storage Temperature -30~+80 °C
Type OLED Graphic Display, OLED Touch Display, Grayscale OLED
No. Symbol Function
1 N.C. Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
2 VSS Ground.
3 VCC Power supply for panel driving voltage.
This is also the most positive power voltage supply pin.
4 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
5 VLSS Analog system ground pin.
6~13 D7~D0 Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
14 E/RD# Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
15 R/W# Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
16 BS0 Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
BS[2:0] Interface
00 4 line SPI
01 3 line SPI
10 8-bit 8080 parallel
11 8-bit 6800 parallel
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
17 BS1
18 D/C# Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
19 CS# Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
20 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
21 FR This pin is No Connection pins. Nothing should be connected to this pin. This pin should be left open individually.
22 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA.
23 N.C. Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
24 VDDIO Power Supply for I/O Pin
It should be matched with the MCU interface voltage level.
25 VDD Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
26 VCI Power Supply for Operation
VCI must always be equal to or higher than VDD and VDDIO.
27 VSL Voltage Output Low Level for SEG Signal
This is segment voltage reference pin.
When external VSL is not used, this pin should be left open.
When external VSL is used, this pin should connect with resistor and diode to ground.
28 VLSS Ground of Analog Circuit
These are the analog ground pins. They should be connected to VSS externally.
29 VCC Power Supply for OLED Panel
These are the most positive voltage supply pin of the chip. They must be connected to external source.
30 N.C. Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.

CTP Pin Function

1 GND Ground
2 VDD Power Supply Voltage of CTP
3 INT External interrupt to the host
4 SDA I2C data input and output
5 SCL I2C clock input
6 RST External Reset, Low is active
7-10 GND Ground.

3.12 inch 256x64 OLED Display with Capacitive Touch - RET025664B-CTP

Absolute Maximum Ratings

Parameter Symbol Min Max Unit
Supply Voltage for Operation VCI -0.3 4 V
Supply Voltage for Logic VDD -0.5 2.75 V
Supply Voltage for I/O Pins VDDIO -0.5 VCI V
Supply Voltage for Display VCC -0.5 20 V
Operating Temperature TOP -20 +70 °C
Storage Temperature TSTG -30 +80 °C

Touch Panel Controller FT6336U

Parameter Symbol Min Max Unit
Power Supply Voltage VDD -0.3 3.6 V

DC Electrical Characteristics

Item Symbol Condition Min Typ Max Unit
Supply Voltage for Operation VCI   2.8 3.0 3.3 V
Supply Voltage for Display VCC 14 14.5 15 V
Logic supply voltage VDD 2.4 2.6 V
Power for I/O pins VDDIO 1.65   VCI V
High Level Input VIH 0.8×VDDIO VDDIO V
Low Level Input VIL 0 0.2×VDDIO V
High Level Output VOH 0.9×VDDIO VDDIO V
Low Level Output VOL 0 0.1×VDDIO V
50% Check Board operating Current VCC =14.5V 32 48 mA

Touch Panel Controller FT6336U

Item Symbol Condition Min Typ Max Unit
Supply Voltage VDD   2.8 3.0 3.3 V
Input High Volt. VIH   0.7xVDD VDD V
Input Low Volt. VIL   -0.3 0.3xVDD V
Output High Volt. VOH IOH = -0.1mA 0.7xVDD V
Output Low Volt. VOL IOH = 0.1mA 0.3xVDD V

3.12 inch 256x64 Graphic OLED Display with Capacitive Touch

Top