3.5 inch CANopen Smart Display IPS TFT with PCAP (Medical Application) - RL0F00035000XGAAASD00
3.5 inch CANopen Smart Display IPS TFT with PCAP (Medical Application) - RL0F00035000XGAAASD00

3.5" CANopen Smart Display IPS TFT with PCAP (Medical Application)

Model No. RL0F00035000XGAAASD00

★3.5 Inch Smart Display Feature:
1.DC 5V working voltage, low power consumption for USB to drive.
2.Self testing after booting function.
3.CAN bus communication interface.
4.Supports CANopen protocol, default baud rate at 250KB.
5.Embedded FLASH memory, storing Font and Object Dictionary.
6.Support capacitive touch panel(CTP).
7.Smart Display scenario is slave device display and action from Master Device instruction.
8.Embedded buzzer controlled by Master Device.
9.Demo set HOST can be used on multiple platforms, such as Computer (with USB to CAN Dongle), MCU, Raspberry Pi (with PiCAN2).

Inquiry or Demo Code Back Previous Next
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Other Specifications
  • Display Usage
  • Description
  • GUI Builder
Item Dimension Unit
Size (Diagonal) 3.5 inch
Dot Matrix / Resolution 320 × 3(RGB) × 240 dots
LCD panel 76.84(W) × 63.84(H) × 4.53 mm
PCB 100(W) × 82(H) × 1.6 mm
Housing Outline NA mm
Module Dimension 76.84(W) × 63.84(H) × 4.53(D) mm
Active Area 70.08(W) × 52.56(H) mm
Dot / Pixel Pitch 0.073(W) × 0.219(H) mm
LCD Type TFT, Normally Black, Transmissive
View Direction 80/80/80/80 (IPS)
Aspect Ratio 4:3
Interface (System) CAN bus differential ± 3.3
Touch Panel Projected Capacitive Touch Screen, PCAP
Surface Glare
Operating voltage 5 Vdc
Operating Temperature -20~+70 °C
Application Medical

CON2 definition:

Pin Symbol Function Remark
16 +5V Power supply 5V input Input
15 GND Power supply GND input Input
14 CAN_High CAN bus D+ I/O
13 CAN_Low CAN bus D- I/O
12 GND Power supply GND input Input
11 GND Power supply GND input Input
10-1 NC Connection -

CON3 definition:

Pin Symbol Function Remark
16 VMCU 3.3V power for JTAG interface Output
15 JTAG_SWCLK CLK pin for JTAG interface Input
14 GND GND for JTAG interface Output
13 JTAG_SWDI Data pin for JTAG interface I/O
12 NRST Reset pin for JTAG interface Input
11 JTAG_SWDO Data pin for JTAG interface I/O
11-1 NC Connection -

3.5 inch CANopen Smart Display IPS TFT with PCAP (Medical Application) - RL0F00035000XGAAASD00

Absolute Maximum Ratings

Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 +70
Storage Temperature TST -30 +80

Electrical Characteristics

 

Operating conditions:

Item Symbol Condition Min Typ Max Unit
Supply Voltage For Analog VCI 4.75 5 5.5 V
Interface Operation Voltage IOVCC 3.234 3.30 3.367 V
Supply LCM current ICI(mA) XXX XXX - mA

LED driving conditions:

Parameter Symbol Min. Typ. Max. Unit
LED current   - 20 - mA
Power Consumption   324 384 408 mW
LED voltage VBL+ 16.2 19.2 20.4 V
LED Life Time   - 50,000 - Hr

 

Bom

Item Description
LCM RFC350X-AYW-DNG
PCBA 4 layer FR4, 1.6mm

Functional description

Smart Display can be used to display the coordinate, status and data information provided by the connected HOST device. Customers can configure the position coordinates they want to display in normal operation mode (Node ID = 0x7B).

 

The Display is designed to be easily connected to a controller network, and to operate with minimum setup or knowledge of the SDO configuration on the controllers.

 

Splash Screen

The default splash image is shown below.

Splash Screen - RL0F00035000XGAAASB00

This product is produced as a generic product. If you require a custom splash image for your application, contact us to discuss.

 

Acquisition of Displayed Data

The Smart Display can acquire the data that it displays either using the CANopen SDO protocol, or using the CANopen PDO protocol.

 

On Pre-operational mode, customers can set the coordinates of objects through SDO; On operational mode, customers can send data of objects through PDO.

 

Configuring the Display

Winstar Smart Display CAN series offers an out-of-the-box CANopen development experience that will lower customers' development costs and speed time-to-market expectations.

 

The Smart Display can use wide-temperature are designed to support control applications in harsh operating conditions, which designed to be connected to a variety of different situation combinations, such as automotive, marine, power generation and oil-and-gas.

 

The Smart Display comes with standard UI objects to get customers project off the ground quickly. If customers need custom UI objects support, our engineers are here to help. Send over your contents in PNG/JPG format, we will send over a new set of UI objects within 3~5 working days.

 

The Smart Display is defined as a slave device, which is controlled by master device via CAN bus command to render display content on the display screen and return touch event data with protocol objects.

 

Example Screen Layout (Medical Application)

Example Layout

The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in an industry application situation.

Example Screen Layout (Medical Application) - RL0F00035000XGAAASD00

 

 

RL0F00035000XGAAASD00, this 3.5-inch CAN bus Smart Display adopts one of our off-the-shelf IPS TFT modules RFC350X-AYW-DNC coupled with coding firmware interface. In the light of the coding firmware, users only need to execute commands of control which cut down on time of programming notably. Such smart display is an excellent solution for faster time-to-market.

 

The Smart Display of Raystar is comprised of our TFT module and CAN interface. There are plenty of advantages of this interface including data transmission of long distance (up to 40 meters), being highly immune to electrical interference, good stability. CAN BUS is the most common physical layer; the maximum transmission rate can reach 1Mb/s (High-Speed CAN). It’s effortless to communicate with other devices supporting CANopen protocol, moreover, there’re various types of objects of control to choose from. On top of that, its flexible parameter control settings allow users for faster development.

 

Smart Display has built-in flash memory (Flash) to store fonts and graphic objects (Object Dictionary). The host can simultaneously control up to 30 Smart Displays and demonstrate different graphic objects. This Smart Display also provides standard UI objects enabling users to swiftly develop projects. If customers need customized UI objects, Raystar’s engineering team is able to provide you with comprehensive help and convert image files in PNG / JPG format into image control objects which can be completed in 3 to 5 working days.

1. Introduction of Raystar Smart Display GUI Builder

 

1-1 Dragging Widgets & preview function:

Users are able to design their screen appearance by dragging widgets on Raystar GUI Builder, and you also get a live preview of the changes. With the concept of "what you see is what you get", this function is time-saving for screen appearance design.

 

1-2 Simulator function:

There’s no need to purchase the hardware (Smart Display) to demonstrate the display effects and interactive behaviors. Users only need to use Raystar GUI Builder application software simulator to simulate the display effects and functions on the computer which greatly reduce costs and speed up project development.

 

1-3 Change or build GUI design on the client-side:

Instead of creating graphical objects through the Raystar engineering team, customers can replace or create GUI designs by themselves. But if customers have any other demands, we can also provide custom-design graphics objects.

 

1-4 How to get Raystar’s GUI Builder?

All you need is to contact us through our website or send inquiries to our sales email address. We'll provide it free of charge.

 

 

2.Smart Display GUI Builder introduction of operation and toolbar

 

2-1 The Start screen of Smart Display GUI Builder

 

The Start screen of Smart Display GUI Builder

 

2-2 The design page of Smart Display GUI Builder

 

The design page of Smart Display GUI Builder

The design page of Smart Display GUI Builder

 

2-3 Customization by Smart Display GUI Builder

 

Customization by Smart Display GUI Builder

 

2-4 Simulation by Smart Display GUI Builder

 

Simulation by Smart Display GUI Builder

 

2-5 HW device update

 

HW device update

 

2-6 The settings of installation

 

Install USB2CAN Driver:

*Execute stlink_winusb_install.bat (Please contact us to get the file)

The settings of installation - Install USB2CAN Driver

 

Install Microsoft Visual C++ 2015-2019 Redistributable (x86)

*Execute VC_redist.x86.exe (Please contact us to get the file)

The settings of installation- Install Microsoft Visual C++ 2015-2019 Redistributable (x86)

 

Install Smart Display GUI Builder

*Execute RaystarSmartDisplayGUIBuilderSetup_v0.1.5.msi (Please contact us to get the file)
*An icon of “Raystar SmartDisplay GUI Builder” will be shown after installing

An icon of “Raystar SmartDisplay GUI Builder” will be shown after installing

Top