- General Specifications
- Interface Pin Function
- Contour Drawing
- Absolute Maximum Ratings
- Electrical Characteristics
- Display Usage
- Advantages & Applications
|Dot Matrix / Resolution||800× 3(RGB) × 480||dots|
|Module Dimension||120.7(W) × 75.8(H) × 4.475||mm|
|Active Area||108(W) × 64.8 (H)||mm|
|Dot / Pixel Pitch||0.135(W) × 0.135(H)||mm|
|View Direction||80/80/80/80 (IPS)|
|Interface (System)||CAN bus differential ± 3.3|
|Touch Panel||Projected Capacitive Touch Screen, PCAP|
|1||+5V||Power supply 5V input||Input|
|2||GND||Power supply GND input||Input|
|3||CAN_High||CAN bus D+||I/O|
|4||CAN_Low||CAN bus D-||I/O|
|5||VDD_5V||5V output for USART interface||Output|
|6||USART1_RX||USART RX interface||Reserve|
|7||USART1_TX||USART TX interface||Reserve|
|8||GND||GND for USART interface||Output|
|PCBA||4 layer FR4, 1.6mm|
Note: Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings listed above 1. Temp. ≦60℃, 90% RH MAX. Temp.＞60℃, Absolute humidity shall be less than 90% RH at 60℃
|Supply Voltage For Analog||VCI||－||4.75||5||5.5||V|
|Interface Operation Voltage||IOVCC||－||3.234||3.30||3.367||V|
|Supply LCM current||ICI(mA)||－||320||350||-||mA|
LED driving conditions
|LED voltage||VBL+||-||-||18||V||Note 1|
|LED Life Time||-||50,000||-||Hr||Note 2,3,4|
Note 1 : There are 1 Groups LED
Note 2 : Ta = 25 ℃
Note 3 : Brightness to be decreased to 50% of the initial value
Note 4 : The single LED lamp case
Smart Display can be used to display the coordinate, status and data information provided by the connected HOST device. Customers can configure the position coordinates they want to display in normal operation mode.
The Display is designed to be easily connected to a controller network, and to operate with minimum setup or knowledge of the SDO configuration on the controllers.
The default splash image is shown below.
This product is produced as a generic product. If you require a custom splash image for your application, contact us to discuss.
Acquisition of Displayed Data
The Smart Display can acquire the data that it displays either using the CANopen SDO protocol, or using the CANopen PDO protocol.
On Pre-operational mode, customers can set the coordinates of objects through SDO; On operational mode, customers can send data of objects through PDO.
Configuring the Display
Raystar Smart Display CAN series offers an out-of-the-box CANopen development experience that will lower customers' development costs and speed time-to-market expectations.
The Smart Display can use wide-temperature are designed to support control applications in harsh operating conditions, which designed to be connected to a variety of different situation combinations, such as automotive, marine, power generation and oil-and-gas.
The Smart Display comes with standard UI objects to get customers project off the ground quickly. If customers need custom UI objects support, our engineers are here to help. Send over your contents in PNG/JPG format, we will send over a new set of UI objects within 3~5 working days.
The Smart Display is defined as a slave device, which is controlled by master device via CAN bus command to render display content on the display screen and return touch event data with protocol objects.
Example Screen Layout (Vehicle automotive)
The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in an vehicle automotive situation.
Example Screen Layout (Industry application)
The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a industry application situation.
Advantages of using CANopen protocol for Smart Displays:
1. As CANopen is a universal protocol (ISO11898), you can plug and play on certain applications such as passenger vehicles, trucks, buses (gasoline vehicles and electric vehicles), etc.
2. The ISO 11898 standard specifies a data rate up to 1 Mbps, maximum CAN bus cable length of 40 m, maximum of 30 nodes. Compared with UART & USB, CAN transmission distance can go up to 40 meters. CAN physical layer is differential pair. It has strong anti-interference ability and good stability.
3. Graphical objects are customizable and can be saved in smart displays.
4. The HOST can control up to 30 Smart Displays and show different graphic objects simultaneously.
CAN Bus Display Applications:
1. Passenger vehicles, trucks, buses (gasoline vehicles and electric vehicles).
2. Agricultural equipment.
3. Electronic equipment for aviation and navigation.
4. Industrial automation and mechanical control.
5. Elevators, escalators.
6. Building automation.
7. Medical instruments and equipment.