- Especificación
- Función Interfaz Pin
- Dibujo Contorno
- Otras Especificaciones
- Uso de La Pantalla
- Descripción
- GUI Builder
| Elemento | Dimensión | Unidad |
|---|---|---|
| Tamaño (Diagonal) | 3.5 | pulgada |
| Matriz de puntos (Resolución) | 320 × 3 (RGB) × 240 | dots |
| Dimensión del módulo | 100 (W) × 82 (H) × 13.2 (D) | mm |
| Área de visión | 71 (W) × 53 (H) | mm |
| zona activa(AA) | 70.08 (W) × 52.56 (H) | mm |
| Distancia entre puntos | 0.219 (W) × 0.219 (H) | mm |
| Tipo de LCD | TFT, Normalmente Negro, Transmisivo | |
| Dirección de la vista | 80/80/80/80 (IPS) | |
| Relación de aspecto | 4:3 | |
| Placa de control | Yes | |
| Interfaz (System) | CAN bus differential ± 3.3 | |
| Protocolo | CAN open | |
| I/O(GPIO) | No | |
| MCU | STM32F750 | |
| Puntos de Detección | 1 | Points |
| Pantalla táctil | Pantalla táctil capacitiva proyectada, PCAP | |
| Superficie | Resplandor (Glare) | |
| Brillo | 400 | cd/㎡ |
| Tensión de Funcionamiento | 5 ~ 24 | Vdc |
| Tamaño de la Memoria Flash | 16 | MB |
| SDRAM Frequency | 108 | Mhz |
| Temperatura de funcionamiento | -20~+70 | °C |
Definición CON2
| Pin No. | Símbolo | Función | Observación |
|---|---|---|---|
| 16 | VIN | Power +5V~24V | Input |
| 15 | GND | Power GND | Input |
| 14 | CAN_H | CAN bus D+ | I/O |
| 13 | CAN_L | CAN bus D- | I/O |
| 12-1 | Reserved | -- | -- |
Definición CON3
| Pin No. | Símbolo | Función | Observación |
|---|---|---|---|
| 16 | +3V3 | 3.3V power for JTAG interface | Output |
| 15 | SWCLK | CLK pin for JTAG interface | Input |
| 14 | GND | GND for JTAG interface | Output |
| 13 | SWDI | Data pin for JTAG interface | I/O |
| 12 | NRST | Reset pin for JTAG interface | Input |
| 11 | SWDO | Data pin for JTAG interface | I/O |
| 10-1 | Reserved | -- | - |
Valores Nominales Máximos Absolutos
| Artículo | Símbolo | Mínimo | Tipo | Máximo | Unidad |
|---|---|---|---|---|---|
| Temperatura Funcionamiento | TOP | -20 | － | +70 | ℃ |
| Temperatura Almacenamiento | TST | -30 | － | +80 | ℃ |
Características Electrónicas
| Artículo | Símbolo | Mínimo | Tipo | Máximo | Unidad |
|---|---|---|---|---|---|
| Tensión de Alimentación | VCC | 5 | 12 | 24 | V |
| Corriente de Alimentación | ICC | - | 150 | - | mA |
Bom
| Item | Description |
|---|---|
| LCM | RFC350X-AYW-DNG |
| PCBA | SV100035000XA00N0101 |
Pantalla de Bienvenida
A continuación se muestra la imagen de bienvenida predeterminada.
This product is produced as a generic product. If you require a custom splash image for your application, contact us to discuss.
Default Selection
Press the preferred application and hold for 3 seconds for the first time power on.
Ejemplo de Estructuración de Pantalla (Aplicación industrial)
Ejemplo de Estructuración de Pantalla (automóvil)
Ejemplo de Estructuración de Pantalla (Aplicación médica)
También proporcionamos un conjunto de demostración con todos los accesorios necesarios para que pueda realizar su diseño de GUI en las pantallas.
1. Introduction of Raystar Smart Display GUI Builder
1-1 Dragging Widgets & preview function:
Users are able to design their screen appearance by dragging widgets on Raystar GUI Builder, and you also get a live preview of the changes. With the concept of "what you see is what you get", this function is time-saving for screen appearance design.
1-2 Simulator function:
There’s no need to purchase the hardware (Smart Display) to demonstrate the display effects and interactive behaviors. Users only need to use Raystar GUI Builder application software simulator to simulate the display effects and functions on the computer which greatly reduce costs and speed up project development.
1-3 Change or build GUI design on the client-side:
Instead of creating graphical objects through the Raystar engineering team, customers can replace or create GUI designs by themselves. But if customers have any other demands, we can also provide custom-design graphics objects.
1-4 How to get Raystar’s GUI Builder?
All you need is to contact us through our website or send inquiries to our sales email address. We'll provide it free of charge.
2.Smart Display GUI Builder introduction of operation and toolbar
2-1 The Start screen of Smart Display GUI Builder
2-2 The design page of Smart Display GUI Builder
2-3 Customization by Smart Display GUI Builder
2-4 Simulation by Smart Display GUI Builder
2-5 HW device update
2-6 The settings of installation
Install USB2CAN Driver:
*Execute stlink_winusb_install.bat (Please contact us to get the file)
Install Microsoft Visual C++ 2015-2019 Redistributable (x86)
*Execute VC_redist.x86.exe (Please contact us to get the file)
Install Smart Display GUI Builder
*Execute RaystarSmartDisplayGUIBuilderSetup_v0.1.5.msi (Please contact us to get the file)
*An icon of “Raystar SmartDisplay GUI Builder” will be shown after installing
