Módulo Pantalla OLED Gráfica COG 0.95 pulgadas 96×64 (IC SSD1315) - REX009664D
Módulo Pantalla OLED Gráfica COG 0.95 pulgadas 96×64 (IC SSD1315) - REX009664D
Módulo Pantalla OLED Gráfica COG 0.95 pulgadas 96×64 (IC SSD1315) - REX009664D
Módulo Pantalla OLED Gráfica COG 0.95 pulgadas 96×64 (IC SSD1315) - REX009664D

Módulo Pantalla OLED Gráfica COG 0.95 pulgadas 96×64 (IC SSD1315)

Model No. REX009664D

El REX009664D es un módulo de pantalla OLED de matriz pasiva de 0.95 pulgadas con estructura COG (Chip-on-Glass). Ofrece una resolución de 96×64 puntos en un formato compacto de 24.9 × 22.95 × 1.61 mm.

Este módulo es compatible con múltiples interfaces, incluyendo 6800, 8080, SPI de 4 hilos y I2C. Está controlado por el IC SSD1315 y funciona con un ciclo de trabajo de 1/64. El REX009664D es ideal para electrodomésticos inteligentes, equipos portátiles industriales y dispositivos médicos.

Admite un amplio rango de temperatura de funcionamiento de -40°C a +80°C. El voltaje lógico (VDD) varía entre 2.4V y 3.3V, y consume típicamente entre 6 y 9 mA con un 50% de píxeles activos.

Si necesita soporte técnico o cotizaciones del REX009664D u otros módulos OLED de 0.95 pulgadas, no dude en contactar a nuestro equipo de ventas.

Fuente de datos: REX009664DYPP3N00000

AÑADIR A PREGUNTA/Demo Code DESCARGAR PDF anterior PREV. SIGUIENTE
  • Especificación
  • Función interfaz Pin
  • DIBUJO
  • Valores nominales máximos absolutos
  • Características electrónicas
Elemento Dimensión Unidad
Estructura COG
Tamaño (Diagonal) 0.95 pulgada
Matriz de puntos (Resolución) 96 × 64 dots
Dimensión del módulo 24.9 × 22.95 × 1.61 mm
Área de visión 21.953 × 15.424 mm
zona activa(AA) 19.946 × 13.418 mm
Tamaño del punto 0.184 × 0.186 mm
Distancia entre puntos 0.208 × 0.21 mm
Color de Emisión OLED, Blanco / Amarillo
Modo de visualización Matriz Pasiva
IC SSD1315
Interfaz 6800 / 8080 / 4-hilos SPI / I2C
Fuente de alimentación 3V
Deber 1/64 Deber
Temperatura de funcionamiento -40~+80 °C
Temperatura de almacenamiento -40~+85 °C
Tipo de polarizador Polarizador opcional
Tipo Pantalla Gráfica OLED
Pin No. Símbolo Función
1 NC No connection
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
3 VSS Ground pin. It must be connected to external ground.
4 NC No connection
5 VDD Power supply pin for core logic operation.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 are pin select
BS[2:1] Interface
00 4 line SPI
01 I2C
11 8-bit 8080 parallel
10 8-bit 6800 parallel
Note
(1) 0 is connected to VSS (2) 1 is connected to VDD
7 BS2
8 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
9 RES# This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
10 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection.
11 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
12 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
13 D0 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
14 D1
15 D2
16 D3
17 D4
18 D5
19 D6
20 D7
21 IREF This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA.
22 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
24 VLSS This is an analog ground pin. It should be connected to VSS externally.
25 NC No connection

Módulo Pantalla OLED Gráfica COG 0.95 pulgadas 96×64 (IC SSD1315) - REX009664D DIBUJO

Parámetro Símbolo Mínimo Tipo Máximo Unidad
Tensión Alimentación para Lógica VDD -0.3 － 4.0 V
Tensión Alimentación para Pantalla VCC 0 － 18.0 V
Temperatura Funcionamiento TOP -40 － +80 °C
Temperatura Almacenamiento TSTG -40 － +85 °C

Características Electrónicas DC

Artículo Símbolo Condición Mínimo Tipo Máximo Unidad
Tensión Alimentación para Lógica VDD － 1.65 3.0 3.3 V
Tensión Alimentación para Pantalla VCC － 7.5 12.0 12.5 V
Entrada Alto Nivel VIH － 0.8×VDD － VDD V
Entrada Bajo Nivel VIL － 0 － 0.2×VDD V
Salida Alto Nivel VOH Iout = 100uA 0.9×VDD － VDD V
Salida Bajo Nivel VOL Iout = 100uA 0 － 0.1×VDD V
Display 50% Pixel on ICC － － 6 9 mA

Related Products

Top