REX012864C - Raystar

0.96 pulgada SH1106 Pantalla Gráfica OLED

Model No. REX012864C

REX012864C es un módulo de pantalla OLED de 0.96 pulgadas con una resolución de 128x64 puntos. Esta pantalla OLED de 0.96 pulgadas utiliza el controlador IC SH1106, que es compatible con la interfaz 6800 / 8080 / SPI / I2C. La pantalla OLED no requiere retroiluminación, lo que resulta en un contraste muy agradable en entornos oscuros, y consume menos energía en comparación con otros tipos de pantallas.

Dos características clave de la pantalla OLED son el convertidor DC/DC elevador integrado y el suministro externo de VCC. El voltaje de alimentación lógica varía de 2.8V a 3.3V, con un valor típico de 3.0V. El módulo opera en un rango de temperatura de -40°C a +80°C; el rango de temperatura de almacenamiento cubre desde -40°C hasta +85℃. Este módulo de pantalla OLED SH1106 de 0.96 pulgadas ofrece diferentes tipos de FPC como ZIF y Hotbar FPC. Los colores de emisión disponibles son blanco y amarillo.

Ref. de la fuente de datos: REX012864CWAP3N00001

AÑADIR A PREGUNTA/Demo Code

DESCARGAR PDF

Elemento	Dimensión	Unidad
Estructura	COG
Tamaño (Diagonal)	0.96	pulgada
Matriz de puntos (Resolución)	128 × 64	dots
Dimensión del módulo	26.70 × 19.26 × 1.26	mm
Área de visión	23.34 × 11.46	mm
zona activa(AA)	21.74 × 10.86	mm
Tamaño del punto	0.148 × 0.148	mm
Distancia entre puntos	0.170 × 0.170	mm
Color de Emisión	OLED, Amarillo / Blanco
Modo de visualización	Matriz Pasiva
IC	SH1106
Interfaz	6800, 8080, 4-hilos SPI, I2C
Fuente de alimentación	3V
Deber	1/64 Deber
Temperatura de funcionamiento	-40~+80	°C
Temperatura de almacenamiento	-40~+85	°C
Tipo de polarizador	Polarizador opcional
Opciones de FPC	Sí
Tipo	Pantalla Gráfica OLED

No.

Símbolo

Función

No connection

C1N

Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.

C1P

C2P

Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.

C2N

VDD2

3.0 – 4.7V power supply pad for Power supply for charge pump circuit.
This pin should be disconnected when VPP is supplied externally

No connection

VSS

Ground.

VDD1

Power supply input: 1.65 - 3.5V

No connection

IM1

These are the MPU interface mode select pads.

	8080	1²C	6800	4-wire SPI
IM1	1	1	0	0
IM2	1	0	1	0

IM2

CSB

This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.

RESB

This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.

This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.

WRB

This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.

RDB

This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.

This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.

IREF

This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.

VCOMH

This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.

VPP

OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.

No connection

REX012864C with Hotbar FPC

0.96 pulgada SH1106 Pantalla Gráfica OLED - REX012864C

REX012864C with ZIF FPC

0.96 pulgada SH1106 Pantalla Gráfica OLED - REX012864C

Parámetro	Símbolo	mínimon	Máximo	Unidad
Tensión de Alimentación para lógica	VDD1	-0.3	3.6	V
Power supply for charge pump circuit	VDD2	-0.3	4.8	V
Tensión de alimentación de la pantalla	VPP	-0.3	14.5	V
Temperatura de funcionamiento	TOP	-40	+80	°C
Temperatura de almacenamiento	TSTG	-40	+85	°C

Características Electrónicas DC

Artículo	Símbolo	Condición	mínimo	Típico	Máximo	Unidad
Tensión de Alimentación para lógica	VDD1	－	2.8	3.0	3.3	V
Power supply for charge pump circuit	VDD2	－	3.5	3.8	4.2	V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC)	Charge Pump VPP	－	7.5	8	8.5	V
Entrada de alto nivel	VIH	－	0.8xVDD1	－	VDD1	V
Entrada de bajo nivel	VIL	－	VSS	－	0.2xVDD1	V
Salida de alto nivel	VOH	－	0.8xVDD1	－	VDD1	V
Salida de bajo nivel	VOL	－	VSS	－	0.2xVDD1	V
Operating Current for VDD2 Display 50% ON	IDD2	－	－	10	16	mA