- Especificación
- Función Interfaz Pin
- Dibujo del Contorno
- Valores Nominales Máximos Absolutos
- Características Electrónicas
| Elemento | Dimensión | Unidad |
|---|---|---|
| Estructura | COG | |
| Tamaño (Diagonal) | 0.91 | pulgada |
| Matriz de puntos (Resolución) | 128 × 32 | dots |
| Dimensión del módulo | 30.0 × 11.5 × 1.26 | mm |
| Área de visión | 24.384 × 7.584 | mm |
| zona activa(AA) | 22.384 × 5.584 | mm |
| Tamaño del punto | 0.152 × 0.152 | mm |
| Distancia entre puntos | 0.175 × 0.175 | mm |
| Color de Emisión | OLED, Amarillo / Blanco / Azul cielo | |
| Modo de visualización | Matriz Pasiva | |
| IC | SSD1306 | |
| Interfaz | I2C | |
| Fuente de alimentación | 3V | |
| Deber | 1/32 Deber | |
| Temperatura de funcionamiento | -40~+80 | °C |
| Temperatura de almacenamiento | -40~+85 | °C |
| Tipo de polarizador | Polarizador opcional | |
| Tipo | Pantalla Gráfica OLED |
| Pin No. | Símbolo | Función |
|---|---|---|
| 1 | C2P | Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
| 2 | C2N | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
| 6 | NC | No connection |
| 7 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
| 8 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
| 9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
| 10 | SCL | I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin inapplication and D0 is the serial clock input, SCL. |
| 11 | SDA | |
| 12 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA. |
| 13 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
| 14 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
| Parámetro | Símbolo | mínimo | Máximo | Unidad |
|---|---|---|---|---|
| Tensión de Alimentación para lógica | VDD | 0 | 4.0 | V |
| Tensión de alimentación de la pantalla | VCC | 0 | 16.0 | V |
| Temperatura de funcionamiento | TOP | -40 | +80 | °C |
| Temperatura de almacenamiento | TSTG | -40 | +85 | °C |
| Elemento | Símbolo | Condición | mínimo | Típico | Máximo | Unidad |
|---|---|---|---|---|---|---|
| Tensión de Alimentación para lógica | VDD | － | 2.8 | 3.0 | 3.3 | V |
| Tensión de alimentación de la pantalla | VCC | － | 7 | 7.25 | 8 | V |
| Entrada de alto tensión | VIH | － | 0.8×VDD | － | VDDIO | V |
| Entrada de baja tensión | VIL | － | 0 | － | 0.2×VDD | V |
| Alta tensión de salida | VOH | － | 0.9×VDD | － | VDDIO | V |
| Baja tensión de salida | VOL | － | 0 | － | 0.1×VDD | V |
| Operating Current for VCC (VCC Supplied Externally) | ICC | Vcc =7.25V | － | 7 | 11 | mA |
