- Especificación
- Función interfaz Pin
- DIBUJO
- Valores nominales máximos absolutos
- Características electrónicas
- Opciones
| Elemento | Dimensión | Unidad |
|---|---|---|
| Estructura | COG | |
| Tamaño (Diagonal) | 0.91 | pulgada |
| Matriz de puntos (Resolución) | 128 × 32 | dots |
| Dimensión del módulo | 30.0 × 11.5 × 1.26 | mm |
| Área de visión | 24.384 × 7.584 | mm |
| zona activa(AA) | 22.384 × 5.584 | mm |
| Tamaño del punto | 0.152 × 0.152 | mm |
| Distancia entre puntos | 0.175 × 0.175 | mm |
| Color de Emisión | OLED, Amarillo / Blanco / Azul cielo | |
| Modo de visualización | Matriz Pasiva | |
| IC | SSD1306 | |
| Interfaz | 4-hilos SPI | |
| Fuente de alimentación | 3V | |
| Deber | 1/32 Deber | |
| Temperatura de funcionamiento | -40~+80 | °C |
| Temperatura de almacenamiento | -40~+85 | °C |
| Opciones de FPC | Yes | |
| Tipo | Pantalla Gráfica OLED |
| Pin No. | Símbolo | Función |
|---|---|---|
| 1 | C2P | Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
| 2 | C2N | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
| 6 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
| 7 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
| 8 | CS# | Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. |
| 9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
| 10 | D/C# | Data/Command Control This pin is Data/Command control pin.. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. |
| 11 | SCLK | When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
| 12 | SDIN | |
| 13 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA. |
| 14 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
| 15 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
| Parámetro | Símbolo | mínimo | Máximo | Unidad |
|---|---|---|---|---|
| Tensión de Alimentación para lógica | VDD | 0 | 4.0 | V |
| Tensión de alimentación de la pantalla | VCC | 0 | 16.0 | V |
| Temperatura de funcionamiento | TOP | -40 | +80 | °C |
| Temperatura de almacenamiento | TSTG | -40 | +85 | °C |
| Elemento | Símbolo | Condición | mínimo | Típico | Máximo | Unidad |
|---|---|---|---|---|---|---|
| Tensión de Alimentación para lógica | VDD | － | 2.8 | 3.0 | 3.3 | V |
| Tensión de alimentación de la pantalla (Supplied Externally) | VCC | － | 7 | 7.25 | 8 | V |
| Suministro de Voltaje del Regulador de Bomba de Carga | VBAT | － | 3.0 | － | 4.2 | V |
| Voltaje de Salida de la Bomba de Carga para Pantalla (Generated by Internal DC/DC) | Charge Pump VCC |
－ | 7.0 | 7.5 | - | V |
| Entrada de alto tensión | VIH | － | 0.8×VDD | － | VDD | V |
| Entrada de baja tensión | VIL | － | 0 | － | 0.2×VDD | V |
| Alta tensión de salida | VOH | － | 0.9×VDD | － | VDD | V |
| Baja tensión de salida | VOL | － | 0 | － | 0.1×VDD | V |
| Operating Current for VCC (VCC Supplied Externally) | ICC | VCC =7.25V | － | 7 | 11 | mA |
| Display 50% Pixel on (VCC Generated by Internal DC/DC) | IBAT | － | － | 15 | 25 | mA |
FPC Opciones
| Dibujo | FPC Length | PIN | Paso | ZIF / HOTBAR FPC | Interfaz | FPC No. | Fecha de Creación |
|---|---|---|---|---|---|---|---|
 |
17.06 | 15 | 0.65 | HOTBAR FPC | SPI | FPC2065001501XXXXX00 | 20140827 |
 |
40.76 | 15 | 0.5 | ZIF FPC | SPI | FPC2050001511XXXXX02 | 20150421 |
 |
11.26 | 14 | 0.62 | HOTBAR FPC | I2C | FPC2062001401XXXXX02 | 20160106 |
