16字x2行 字元型 COG OLED 顯示器 - REX001602H
16字x2行 字元型 COG OLED 顯示器 - REX001602H
16字x2行 字元型 COG OLED 顯示器 - REX001602H

OLED 16x2 字元型 OLED 顯示器

Model No. REX001602H

REX001602H 是 16字x 2行 COG 字元型 OLED 顯示器模組，模組尺寸為39.1x15.8 mm，有效區域30.69x5.94 mm (對角線1.23吋)。 這款 OLED 模組內建RS0012 IC，支援8-bit/4-bit 6800, 8-bit/4-bit 8080, SPI和I2C介面。此款OLEDE 具有10,000：1的高對比度，提供3V電源電壓。REX001602H OLED 模組工作溫度範圍 -40 to +80℃, 儲存溫度範圍 -40 to +85℃。OLED顏色有白色、黃色可選。

規格來源: REX001602HWPP3N00000

產品詢問 規格書下載 回上頁 上一個產品
  • 一般規格
  • Pin功能定義
  • 規格圖
  • 最大絕對額定值
  • 電氣特性
  • 影片
項目 規格內容 單位
結構 COG
對角線尺寸 1.23 吋
字 × 行 16字 × 2行
模組尺寸 39.1 × 15.8 × 2.01 (MAX) mm
可視區域(VA) 32.69 × 7.94 mm
有效區域(AA) 30.69 × 5.94 mm
點(像素)大小 0.297 × 0.315 mm
點(像素)間距 0.342 × 0.36 mm
字元大小 1.66 × 2.835 mm
字元間距 1.935 × 3.105 mm
發光色 OLED, 白色 / 黃色
IC RS0012
介面 6800, 8080, SPI, I2C
電源電壓 3V
驅動方式(Duty) 1/16 duty
偏光片類型(Polarizer Type) 可選偏光鏡
類型 字元型OLED顯示器
Pin No. 符號 Pin 類型 功能說明
1 GND P Ground Pin
2 V16 I This is the most positive voltage supply pin of the chip. It can be supplied externally or generated internally by using internal DC-DC voltage converter.
3 VCI P DCDC buffer Power Supply
4 GND P Ground Pin
5 VCC P Power Pin
6 BVR I Brightness control pin. It should be connected to VCC.
7 DVR I Pre charge time control. It should be connected to VCC.
8 VBREF O This pin is the internal voltage reference of DCDC1 circuit. A stabilization capacitor should be connected between this pin and GND
9 RESE I NMOS source input pin:
This pin connects to the source current pin of the external NMOS of the booster circuit.
10 GDR O Gate drive pulse output pin:
This output pin drives the gate of external NMOS of the booster circuit.
11 FB I Feedback voltage input pin:
This pin is the feedback resistor input of the booster circuit. It is used to adjust the booster output voltage level.
12 VDD P Power Pin (connect to stabilization capacitor)
13 IM1 I Interface selection
IM1 IM0 Interface
L L 6800-series
L H 8080-series
H L SPI
H H I2C
14 IM0 I
15 RESETB I Reset pin
16 RS I Register Select Input Pin
When this pin is set to "0", it is used as an Instruction Register.
When this pin is set to "1", it is used for as the Data Register.
17 CSB I Chip select input pins
Data / instruction I/O is enabled only when CSB is “L”.
18 RDB I Read / Write execution control pin
MPU Type RDB Description
6800-series E Read / Write control input pin
- RW = “H”: When E is “H”, DB0 to DB7 are in an output status.
- RW = “L”: The data on DB0 to DB7 are latched at the falling edge the E signal.
8080-series RDB Read enable clock input pin
When / RDB is “L”, DB0 to DB7 are in an output status.
19 WRB I Read / Write execution control pin
MPU Type WRB Description
6800-series RW Read / Write control input pin
- RW = “H” : read
- RW = “L” : write
8080-series WRB Write enable clock input pin.
The data on DB0 to DB7 are latched at the rising edge of the /WRB signal.
20 SDA I/O SDA is the serial data input for I2C.
21 SDC I/O SDC is the serial clock input/output for I2C.
22~25 DB7~DB4 I/O High Order Bidirectional Data I/O Pins
These pins are used for data transfer and reception between the MPU and WS0012.
When SPI is selected, DB5 will be the serial clock input: SCL
DB7 will be the serial data input: SDI.
DB6 will be the serial data output: SDO.
26~29 DB3~DB0 I/O Low Order Bidirectional Data I/O Pins
These pins are used for data transfer and reception between the MPU and WS0012.
These pins are not used during a 4-bit operation.
30 GND P Ground Pin

16x2 OLED Character Display Module - REX001602H

項目 符號 最小值 最大值 單位
工作溫度 TOP -40 +80 °C
儲存溫度 TST -40 +85 °C
邏輯電源電壓 VCC -0.3 3.6 V
DCDC轉換器電源電壓 VCI -0.3 3.6 V
顯示器電源電壓 V16 -0.3 19.0 V

 

DC 電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VCC － 2.6 3.3 3.5 V
DCDC轉換器電源電壓 VCI － 2.6 3.3 3.5 V
顯示器電源電壓 V16 － － 12.5 13.0 V
輸入高電壓 VIH － 0.9xVCC － VCC V
輸入低電壓 VIL － GND － 0.1xVCC V
輸出高電壓 VOH IOH=-0.5mA 0.8xVCC － VCC V
輸出低電壓 VOL IOL=0.5mA GND － 0.2xVCC V
50%顯示畫面耗電流 I16 V16=12.5V － 2 4 mA

16字x2行 字元型 COG OLED 顯示器

相關產品

Top