0.96吋 SH1106 OLED 顯示器模組- REX012864C
0.96吋 SH1106 OLED 顯示器模組- REX012864C
0.96吋 SH1106 OLED 顯示器模組- REX012864C
0.96吋 SH1106 OLED 顯示器模組- REX012864C

0.96吋 SH1106 OLED 顯示器模組

Model No. REX012864C

REX012864C 為有效區域 0.96吋 OLED 顯示器，解析度128x64像素，使用 SH1106 驅動器IC，可支援 6800 / 8080 / SPI / I2C 四種介面。OLED 自體發光不需要背光，與其他顯示器相比，OLED 耗電少在黑暗環境中對比度非常好具有10,000：1的高對比度。此系列 0.96” SH1106 OLED 模組提供內部 DC/DC 升壓轉換器和外部VCC供電。可有 ZIF FPC 和 Hotbar FPC可選擇。

★ 可選其它 FPC，請參閱下方"選項"

規格來源: REX012864CWAP3N00001

產品詢問 規格書下載 規格書下載 回上頁 上一個產品 下一個產品
  • 一般規格
  • Pin功能定義
  • 規格圖
  • 最大絕對額定值
  • 電氣特性
  • 選項
項目 規格內容 單位
結構 COG
對角線尺寸 0.96 吋
點陣/解析度 128 × 64 dots
模組尺寸 26.70 × 19.26 × 1.26 mm
可視區域(VA) 23.34 × 11.46 mm
有效區域(AA) 21.74 × 10.86 mm
點(像素)大小 0.148 × 0.148 mm
點(像素)間距 0.170 × 0.170 mm
發光色 OLED, 白色 / 黃色
顯示模式 被動矩陣 (Passive Matrix)
IC SH1106
介面 6800, 8080, 4線SPI, I2C
電源電壓 3V
驅動方式(Duty) 1/64 duty
工作溫度 -40~+80 °C
儲存溫度 -40~+85 °C
偏光片類型(Polarizer Type) 可選偏光鏡
可選FPC 是
類型 繪圖型OLED顯示器
No. 符號 功能說明
1 NC No connection
2 C1N Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.
3 C1P
4 C2P Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.
5 C2N
6 VDD2 3.0 – 4.7V power supply pad for Power supply for charge pump circuit.
This pin should be disconnected when VPP is supplied externally
7 NC No connection
8 VSS Ground.
9 VDD1 Power supply input: 1.65 - 3.5V
10 NC No connection
11 IM1 These are the MPU interface mode select pads.
  8080 12C 6800 4-wire SPI
IM1 1 1 0 0
IM2 1 0 1 0
12 IM2
13 CSB This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
14 RESB This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
15 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
16 WRB This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.
17 RDB This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.
18 D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
27 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
28 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
29 NC No connection
30 NC No connection

REX012864C (Hotbar FPC)

0.96吋 SH1106 OLED 模組 (Hotbar FPC) - REX012864C

 

REX012864C (ZIF FPC)

0.96吋 SH1106 OLED 模組 (ZIF FPC) - REX012864C

參數 符號 最小值 最大值 單位
邏輯電源電壓 VDD1 -0.3 3.6 V
電荷幫浦電源 VDD2 -0.3 4.8 V
顯示電源電壓 VPP -0.3 14.5 V
工作溫度 TOP -40 +80 °C
儲存溫度 TSTG -40 +85 °C

DC 電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VDD1 － 2.8 3.0 3.3 V
電荷幫浦電源 VDD2 － 3.5 3.8 4.2 V
顯示器的電荷幫浦輸出電壓
(Generated by Internal DC/DC)		 Charge Pump
VPP		 － 7.5 8 8.5 V
輸入高準位 VIH － 0.8xVDD1 － VDD1 V
輸入低準位 VIL － VSS － 0.2xVDD1 V
輸出高準位 VOH － 0.8xVDD1 － VDD1 V
輸出低準位 VOL － VSS － 0.2xVDD1 V
VDD2顯示器工作電流為50％ON IDD2 － － 10 16 mA

可選FPC

圖示 FPC 長度 PIN pitch ZIF / HOTBAR FPC 介面 FPC No. 建立日期
 FPC2070003001XXXXX09_REX012864C 13 30 0.7 HOTBAR FPC 6800, 8080, 4-Wire SPI, I2C FPC2070003001XXXXX09 20180613
 FPC2050003011XXXXX23_REX012864C 40.95 30 0.5 ZIF  6800, 8080, SPI, I2C FPC2050003011XXXXX23 20190412

相關產品

Top