0.66 吋 64×48 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX006448B
0.66 吋 64×48 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX006448B
0.66 吋 64×48 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX006448B

0.66 吋 64×48 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）

Model No. REX006448B

REX006448B 是一款 0.66 吋的繪圖型 OLED 顯示器模組，採用 COG（Chip-on-glass）結構，具備 64×48 解析度與單色顯示。模組尺寸為 18.46 × 18.10 × 1.26 mm，非常適合小型裝置的應用場景。

此模組採用 1/48 duty 驅動，內建 SSD1315 IC，支援 6800、8080、4-wire SPI 和 I2C 多種通訊介面，便於系統整合。提供白色與黃色兩種發光顏色，適用於多種嵌入式應用，具備良好的視覺清晰度。

REX006448B 可在 -30°C 至 +70°C 的溫度範圍內穩定運作，邏輯電壓支援 1.65V 至 3.3V，驅動電壓（VCC）為 6.0V 至 8.0V，具備低功耗特性，非常適合用於可攜式設備、小型控制面板及工業設備。

如需 REX006448B 或其他 64×48 OLED 顯示器模組的技術支援或報價，歡迎聯繫我們的業務團隊！

規格來源: REX006448BWPP3N0Y000

產品詢問 規格書下載 回上頁 上一個產品 下一個產品
  • 一般規格
  • Pin 功能定義
  • 規格圖
  • 最大絕對額定值
  • 電氣特性
項目 規格內容 單位
結構 COG
對角線尺寸 0.66 吋
點陣/解析度 64 × 48 dots
模組尺寸 18.46 × 18.10 × 1.26 mm
可視區域(VA) 15.42 × 12.06 mm
有效區域(AA) 13.42 × 10.06 mm
點(像素)大小 0.185 × 0.185 mm
點(像素)間距 0.210 × 0.210 mm
發光色 OLED, 白色 / 黃色
支援灰階 無
顯示模式 Passive Matrix（被動矩陣）
IC SSD1315
介面 6800,8080,4 -wire SPI,I2C
電源電壓 3V
驅動方式(Duty) 1/48 Duty
工作溫度 -30~+70 °C
儲存溫度 -30~+70 °C
偏光片類型(Polarizer Type) 可選
類型 繪圖型 OLED
No. 符號 功能說明
1 ESD_GND It should be connected to ground.
2 C2N C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
3 C2P
4 C1P
5 C1N
6 VBAT

Power supply for charge pump regulator circuit.

 

Status VBAT VDD VCC
Enable charge pump Connect to external VBAT source Connect to external VDD source A capacitor should be connected between this pin and VSS
Disable charge pump Keep float Connect to external VDD source Conect to external VCC source

 
7 VSS This is a ground pin.
8 VDD Power supply pin for core logic operation
9 BS1

These pins are MCU interface selection input.
See the following table:

 

  BS1 BS2
I2C 1 0
4-wire SPI 0 0
8-bit 6800 Parallel 0 1
8-bit 8080 Parallel 1 1

 
10 BS2
11 CS# The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
12 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
13 D/C# This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred
14 R/W# This is read / write control input pin connecting to the MCU interface. When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS.
15 E/RD# This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS.
16~23 D0~D7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
24 IREF This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA.
When internal IREF is used, this pin should be kept NC.
25 VCOMH COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.
26 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS
27 VLSS This is an analog ground pin. It should be connected to VSS externally.
28 ESD GND It should be connected to ground.

0.66 吋 64×48 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX006448B 規格圖

參數 符號 最小值 最大值 單位
電源電壓 VDD 0 4.0 V
電荷幫浦穩壓器電源電壓 VBAT 0 6.0 V
顯示電源電壓 VCC 0 18.0 V
工作溫度 TOP -30 +70 °C
儲存溫度 TSTG -30 +70 °C
項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VDD － 1.65 3.0 3.3 V
顯示電源電壓(Supplied Externally) VCC － 6.0 7.5 8.0 V
電荷幫浦穩壓器電源電壓 VBAT － 3.0 3.3 4.5  V
顯示器的電荷幫浦輸出電壓(Generated by Internal DC/DC) Charge Pump VCC   － 7.0 7.5 － V
輸入高電壓 VIH － 0.8×VDD － VDD V
輸入低電壓 VIL － 0 － 0.2×VDD V
輸出高電壓 VOH － 0.9×VDD － VDD V
輸出低電壓 VOL － 0 － 0.1×VDD V
50%顯示畫面耗電流(VCC Supplied Externally) ICC VPP=7.5V － 3  6  mA
50%顯示畫面耗電流(VCC Generated by Internal DC/DC) IBAT  － － 15 30 mA

相關產品

Top