0.96 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX012864AB
0.96 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX012864AB
0.96 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX012864AB

0.96 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）

Model No. REX012864AB

REX012864AB 是一款 0.96 吋 128×64 COG 被動矩陣 繪圖型 OLED 顯示器模組。其模組尺寸為 24.7 × 16.59 × 1.26 mm，內建 SSD1315 IC，支援 6800、8080、SPI 和 I2C 多種介面，能無縫整合至各類嵌入式系統。此模組提供雙色（黃色與天藍色）發光顏色，方便在使用者介面設計中創造清晰分隔的視覺效果。

為了耐用與多功能而設計，REX012864AB 可在 -30°C 至 +70°C 的溫度範圍內穩定運作，並支援高達 4V 的邏輯電壓供應，非常適合應用於手持裝置、攜帶式儀器與小型控制系統。

如需 REX012864AB 或其他 0.96 吋 OLED 顯示器模組的技術支援或產品報價，歡迎聯繫我們的業務團隊！

資料來源參考：REX012864ABXPP3N0Y000

產品詢問 規格書下載 回上頁 上一個產品 下一個產品
  • 一般規格
  • Pin 功能定義
  • 規格圖
  • 最大絕對額定值
  • 最大絕對額定值
  • 影片
項目 規格內容 單位
結構 COG
對角線尺寸 0.96 吋
點陣/解析度 128 × 64 dots
模組尺寸 24.7 × 16.59 × 1.26 mm
可視區域(VA) 22.74 × 12.2 mm
有效區域(AA) 21.74 × 11.2 mm
點(像素)大小 0.15 × 0.15 mm
點(像素)間距 0.17 × 0.17 mm
發光色 黃色+天空藍（雙色）
支援灰階 無
顯示模式 被動矩陣（Passive Matrix）
IC SSD1315
介面 6800,8080,3線/4線-SPI,I2C
電源電壓 3V
驅動方式(Duty) 1/64
工作溫度 -30~+70 °C
儲存溫度 -30~+70 °C
偏光片類型(Polarizer Type) 可選偏光片
類型 繪圖型OLED顯示器
Pin No. 符號 功能說明
1 N.C. (GND) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2 C2P C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
3 C2N
4 C1P
5 C1N
6 VBAT This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
7 NC NC
8 VSS This is a ground pin.
9 VDD Power supply pin for core logic operation.
10 BS0 These pins are MCU interface selection input. See the
following table:
  BS0 BS1 BS2
I2C 0 1 0
3-wire SPI 1 0 0
4-wire SPI 0 0 0
8-bit 68XX Parallel 0 0 1
8-bit 80XX Parallel 0 1 1
11 BS1
12 BS2
13 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
14 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
16 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18~25 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D2 should be either tied LOW or tied together with D1 as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
26 IREF When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.
When internal IREF is used, this pin should be kept NC.
27 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
29 VLSS This is an analog ground pin. It should be connected to VSS externally.
30 NC
(GND)		 The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

0.96 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX012864AB 規格圖

參數 符號 最小值 最大值 單位
邏輯電源電壓 VDD 0 4 V
電荷幫浦穩壓器電源電壓 VBAT -0.3 6.0 V
顯示電源電壓 VCC 0 18.0 V
工作溫度 TOP -30 +70 °C
儲存溫度 TSTG -30 +70 °C

DC 電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VDD － 1.65 3.0 3.3 V
顯示電源電壓
(Supplied Externally)		 VCC － 7.5 8.0 8.5 V
電荷幫浦穩壓器電源電壓 VBAT － 3.0 3.5 4.2 V
顯示器的電荷幫浦輸出電壓 (Generated by Internal DC/DC) Charge Pump
VCC		 － 7.0 7.5 － V
輸入高準位 VIH － 0.8×VDD － VDD V
輸入低準位 VIL － 0 － 0.2×VDD V
輸出高準位 VOH － 0.9×VDD － VDD V
輸出低準位 VOL － 0 － 0.1×VDD V
Operating Current for VCC (Display 50% Pixel on)
(VCC Supplied Externally)		 ICC VCC =8V － 5.0 7.5 mA
Display 50% Pixel on
(VCC Generated by Internal DC/DC)		 IBAT VBAT=3.5V － 15 22.5 mA

[REX012864AB] 0.96吋雙色OLED顯示器模組展示影片

 

相關產品

Top