1.54 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC）- REX012864A
1.54 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC）- REX012864A
1.54 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC）- REX012864A
1.54 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC）- REX012864A

1.54 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC）

Model No. REX012864A

REX012864A 是一款 1.54 吋 128×64 COG 繪圖型 OLED 顯示器模組，模組尺寸為 42.04 × 27.22 × 1.41 mm，採用 1/64 duty 驅動，內建 SSD1309 IC，支援 6800、8080、4-wire SPI 及 I2C 介面。SPI 介面可提供高速、全雙工傳輸，且佈線簡單，非常適合用於小型且對性能要求高的 OLED 顯示應用。REX012864A 提供多種 FPC 選項，包括 ZIF 與 Hotbar FPC，並有白光、黃光及綠光三種發光顏色可選。

REX012864A 專為多樣的環境下的穩定運行而設計，工作溫度範圍為 -40°C 至 +80°C，邏輯電壓範圍為 1.65–3.3 V。其 COG 結構、多元連接介面、SPI 傳輸優勢及靈活的 FPC 配置，使其適用於工業設備、手持裝置及小型控制系統。

如需 REX012864A 或其他 128×64 SPI OLED 顯示器模組的技術支援或報價，歡迎與我們的業務團隊聯繫。

資料來源：REX012864AYAP3N00000

產品詢問 規格書下載 回上頁 上一個產品 下一個產品
  • 一般規格
  • Pin功能定義
  • 規格圖
  • 最大絕對額定值
  • 電氣特性
  • 選項
項目 規格內容 單位
結構 COG
對角線尺寸 1.54 吋
點陣/解析度 128 × 64 dots
模組尺寸 42.04 × 27.22 × 1.41 mm
可視區域(VA) 37.05 × 19.52 mm
有效區域(AA) 35.05 × 17.51 mm
點(像素)大小 0.249 × 0.249 mm
點(像素)間距 0.274 × 0.274 mm
發光色 OLED, 白色 / 黃色 / 綠色
顯示模式 被動矩陣（Passive Matrix）
IC SSD1309
介面 6800, 8080, SPI, I2C
電源電壓 3V
驅動方式(Duty) 1/64 duty
偏光片類型(Polarizer Type) 可選偏光鏡
可選FPC 是
類型 繪圖型OLED顯示器
Pin No. 符號 功能說明
1 NC(GND) No connection
2 VLSS This is an analog ground pin
3 VSS Ground.
4 NC No connection
5 VDD Power supply pin for core logic operation
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68xx Parallel 0 1
8-bit 80xx Parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
7 BS2
8 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
9 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
10 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
11 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
12 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
13-20 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
21 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
22 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
24 NC(GND) No connection

1.54 吋 128x64 COG 繪圖型 OLED 顯示器模組（SSD1309 IC）- REX012864A 規格圖

參數 符號 最小值 最大值 單位
邏輯電源電壓 VDD -0.3 4 V
顯示電源電壓 VCC 0 17 V
工作溫度 TOP -40 +80 °C
儲存溫度 TSTG -40 +85 °C

DC 電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VDD － 1.65 3.0 3.3 V
顯示電源電壓 VCC － 7.0 12.5 13.0 V
輸入高準位 VIH － 0.8×VDD － － V
輸入低準位 VIL － － － 0.2×VDD V
輸出高準位 VOH － 0.9×VDD － － V
輸出低準位 VOL － － － 0.1×VDD V
顯示 50% 像素 VCC =12.5V － 16 45 mA

可選FPC

圖示 FPC長度 PIN Pitch ZIF / HOTBAR FPC 介面 FPC No. 建立日期
 FPC2050002411XXXXX05_REX012864A 37.19 24 0.5 ZIF 6800/8080/4-SPI/I2C FPC2050002411XXXXX05 20160627
 FPC2050003011XXXXX32_REX012864A 51.05 30 0.5 ZIF 6800/8080/4-SPI/I2C FPC2050003011XXXXX32 20190926

 

相關產品

Top