- 一般規格
- Pin功能定義
- 規格圖
- 最大絕對額定值
- 電氣特性
- 選項
| 項目 | 規格內容 | 單位 |
|---|---|---|
| 結構 | COG | |
| 對角線尺寸 | 0.91 | 吋 |
| 點陣/解析度 | 128 × 32 | dots |
| 模組尺寸 | 30.0 × 11.5 × 1.26 | mm |
| 可視區域(VA) | 24.384 × 7.584 | mm |
| 有效區域(AA) | 22.384 × 5.584 | mm |
| 點(像素)大小 | 0.152 × 0.152 | mm |
| 點(像素)間距 | 0.175 × 0.175 | mm |
| 發光色 | OLED, 白色 / 黃色 / 天空藍 | |
| 顯示模式 | 被動矩陣（Passive Matrix） | |
| IC | SSD1306 | |
| 介面 | 4-wire SPI | |
| 電源電壓 | 3V | |
| 驅動方式(Duty) | 1/32 duty | |
| 工作溫度 | -40~+80 | °C |
| 儲存溫度 | -40~+85 | °C |
| 可選FPC | 是 | |
| 類型 | 繪圖型OLED顯示器 |
| Pin No. | 符號 | 功能說明 |
|---|---|---|
| 1 | C2P | Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
| 2 | C2N | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
| 6 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
| 7 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
| 8 | CS# | Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. |
| 9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
| 10 | D/C# | Data/Command Control This pin is Data/Command control pin.. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. |
| 11 | SCLK | When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
| 12 | SDIN | |
| 13 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA. |
| 14 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
| 15 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
| 項目 | 符號 | 最小值 | 最大值 | 單位 |
|---|---|---|---|---|
| 邏輯電源電壓 | VDD | 0 | 4.0 | V |
| 顯示電源電壓 | VCC | 0 | 16.0 | V |
| 工作溫度 | TOP | -40 | +80 | °C |
| 儲存溫度 | TSTG | -40 | +85 | °C |
| 項目 | 符號 | 條件 | 最小值 | 典型值 | 最大值 | 單位 |
|---|---|---|---|---|---|---|
| 邏輯電源電壓 | VDD | － | 2.8 | 3.0 | 3.3 | V |
| 顯示電源電壓 (Supplied Externally) | VCC | － | 7 | 7.25 | 8 | V |
| 電荷幫浦穩壓器電源電壓 | VBAT | － | 3.0 | － | 4.2 | V |
| 顯示器的電荷幫浦輸出電壓 (Generated by Internal DC/DC) | Charge Pump VCC |
－ | 7.0 | 7.5 | - | V |
| 輸入高電壓 | VIH | － | 0.8×VDD | － | VDD | V |
| 輸入低電壓 | VIL | － | 0 | － | 0.2×VDD | V |
| 輸出高電壓 | VOH | － | 0.9×VDD | － | VDD | V |
| 輸出低電壓 | VOL | － | 0 | － | 0.1×VDD | V |
| VCC工作電流（VCC由外部提供 | ICC | VCC =7.25V | － | 7 | 11 | mA |
| 50%顯示畫面耗電流 (VCC Generated by Internal DC/DC) | IBAT | － | － | 15 | 25 | mA |
可選FPC
| 圖示 | FPC 長度 | PIN | pitch | ZIF / HOTBAR FPC | 介面 | FPC No. | 鍵立日期 |
|---|---|---|---|---|---|---|---|
 |
17.06 | 15 | 0.65 | HOTBAR FPC | SPI | FPC2065001501XXXXX00 | 20140827 |
 |
40.76 | 15 | 0.5 | ZIF FPC | SPI | FPC2050001511XXXXX02 | 20150421 |
 |
11.26 | 14 | 0.62 | HOTBAR FPC | I2C | FPC2062001401XXXXX02 | 20160106 |
