- 一般規格
- Pin功能定義
- 規格圖
- 最大絕對額定值
- 電氣特性
- 影片
| 項目 | 規格內容 | 單位 |
|---|---|---|
| 結構 | COG | |
| 對角線尺寸 | 0.96 | 吋 |
| 點陣/解析度 | 128 × 64 | dots |
| 模組尺寸 | Ø39.4 × 24.8 | mm |
| 可視區域(VA) | 22.74 × 11.86 | mm |
| 有效區域(AA) | 21.74 × 10.86 | mm |
| 點(像素)大小 | 0.148 × 0.148 | mm |
| 點(像素)間距 | 0.17 × 0.17 | mm |
| 發光色 | OLED, 白色 / 黃色 / 藍色 | |
| 顯示模式 | 被動矩陣 (Passive Matrix) | |
| IC | SSD1306 | |
| 介面 | 4線SPI , I2C | |
| 電源電壓 | 3V | |
| 驅動方式(Duty) | 1/64 | |
| 工作溫度 | -20~+70 | °C |
| 儲存溫度 | -30~+80 | °C |
| 類型 | 繪圖型OLED顯示器 |
| Pin No. | 符號 | 功能說明 | ||||||
|---|---|---|---|---|---|---|---|---|
| 1 | VSS | Ground pin. | ||||||
| 2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | ||||||
| 3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||
| 4 | VCI | Power supply pin for core logic operation | ||||||
| 5 | NC | No connection | ||||||
| 6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table.
(1) 0 is connected to VSS (2) 1 is connected to VCI |
||||||
| 7 | IREF | This is segment output current reference pin. When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA. |
||||||
| 8 | CS# | This pin is the chip select input. (active LOW). | ||||||
| 9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH during normal operation. |
||||||
| 10 | D/C# | When 4-wire serial interface is selected, this pin is Data/Command control pin connecting to the MCU. In I2C mode, this pin acts as SA0 for slave address selection. |
||||||
| 11 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||
| 12 | D1 | |||||||
| 13 | D2 | |||||||
| 14 | NC | No connection | ||||||
| 15 | NC | No connection | ||||||
| 16 | NC | No connection | ||||||
| 17 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | ||||||
| 18 | VSS | Ground pin. |
編碼器 PIN 定義
| No. | 符號 | 功能說明 |
|---|---|---|
| 1 | FSW_A | Encoder terminal signal-A |
| 2 | FSW_B | Encoder terminal signal-B |
| 3 | FSW_C | Encoder terminal signal-C |
| 4 | FSW_D | Ground |
| 項目 | 符號 | 最小值 | 最大值 | 單位 |
|---|---|---|---|---|
| 電源電壓 | VCI | -0.3 | 4.0 | V |
| 顯示電源電壓 | VCC | 0 | 15 | V |
| 工作溫度 | TOP | -20 | +70 | °C |
| 儲存溫度 | TST | -30 | +80 | °C |
DC 電氣特性
| 項目 | 符號 | 條件 | 最小值 | 典型值 | 最大值 | 單位 |
|---|---|---|---|---|---|---|
| 電源電壓 | VCI | － | 1.65 | 3.0 | 3.3 | V |
| 顯示電源電壓 | VCC | － | 6 | 10 | 10.5 | V |
| 輸入高準位 | VIH | － | 0.8xVCI | － | － | V |
| 輸入低準位 | VIL | － | － | － | 0.2xVCI | V |
| 輸出高準位 | VOH | Iout = 100uA | 0.9xVCI | － | － | V |
| 輸出低準位 | VOL | Iout = 100uA | － | － | 0.1xVCI | V |
| VCC的工作電流（VCC由外部提供） | ICC | VCC =10V | － | 5 | 10 | mA |
