RET025664B-CTP - Raystar

Article	Dimensions	Unité
Structure	COF
Taille (diagonale)	3.12	pouces
Résolution matricielle	256 × 64	points
Dimensions du module	89.2 × 29.0 × 3.17	mm
Surface de visée (VA)	78.78 × 21.18	mm
Aire active (AA)	76.778 × 19.178	mm
Taille de point et de pixel	0.278 × 0.278	mm
Espacement de point et de pixel	0.300 × 0.300	mm
Couleur émise	OLED, Blanc / Jaune / Vert / Bleu
Prise en charge de la gamme de gris	Yes
Mode d’affichage	Matrice passive
Gamme de gris	4 bits
IC	SSD1322 (COF)
Interface	6800,8080,SPI
PCAP IC	FT6336U
Interface PCAP	I2C
Points de détection	1	Points
Pavé tactile	pavé tactile capacitif
Surface	Reflets
Tension d’alimentation	3V
Duty	1/64 Duty
Température de fonctionnement	-20~+70	°C
Température de rangement	-30~+80	°C
Type	Affichage OLED graphiques,Écran tactile OLED

No.

Symbole

Fonction

N.C.

Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.

VSS

Ground.

VCC

Power supply for panel driving voltage.
This is also the most positive power voltage supply pin.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VLSS

Analog system ground pin.

6~13

D7~D0

Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.

E/RD#

Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.

R/W#

Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.

BS0

Communicating Protocol Select
These pins are MCU interface selection input. See the following table:

BS[2:0]	Interface
00	4 line SPI
01	3 line SPI
10	8-bit 8080 parallel
11	8-bit 6800 parallel

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO

BS1

D/C#

Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.

CS#

Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.

RES#

This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.

This pin is No Connection pins. Nothing should be connected to this pin. This pin should be left open individually.

IREF

Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA.

N.C.

Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.

VDDIO

Power Supply for I/O Pin
It should be matched with the MCU interface voltage level.

VDD

Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS

VCI

Power Supply for Operation
VCI must always be equal to or higher than VDD and VDDIO.

VSL

Voltage Output Low Level for SEG Signal
This is segment voltage reference pin.
When external VSL is not used, this pin should be left open.
When external VSL is used, this pin should connect with resistor and diode to ground.

VLSS

Ground of Analog Circuit
These are the analog ground pins. They should be connected to VSS externally.

VCC

Power Supply for OLED Panel
These are the most positive voltage supply pin of the chip. They must be connected to external source.

N.C.

Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.

Fonction PIN CTP

1	GND	Ground
2	VDD	Power Supply Voltage of CTP
3	INT	External interrupt to the host
4	SDA	I2C data input and output
5	SCL	I2C clock input
6	RST	External Reset, Low is active
7-10	GND	Ground.

3,12 po afficheur OLED graphique 256x64 avec écran tactile PCAP - RET025664B-CTP

Valeurs absolues maximales

Paramètre	Symbole	Min	Max	Unité
Supply Voltage for Operation	VCI	-0.3	4	V
Tension d’alimentation pour le circuit logique	VDD	-0.5	2.75	V
Supply Voltage for I/O Pins	VDDIO	-0.5	VCI	V
Tension d’alimentation pour l’	VCC	-0.5	20	V
Température de fonctionnement	TOP	-20	+70	°C
Température de rangement	TSTG	-30	+80	°C

Contrôleur de l’écran tactile FT6336U

Paramètre	Symbole	Min	Max	Unité
Power Supply Voltage	VDD	-0.3	3.6	V

DC Paramètres électriques

Item	Symbole	Condition	Min	Typ	Max	Unité
Supply Voltage for Operation	VCI		2.8	3.0	3.3	V
Tension d’alimentation pour l’affichage	VCC	－	14	14.5	15	V
Logic supply voltage	VDD	－	2.4	－	2.6	V
Power for I/O pins	VDDIO	－	1.65		VCI	V
Entrée à niveau élevé	VIH	－	0.8×VDDIO	－	VDDIO	V
Entrée à bas niveau	VIL	－	0	－	0.2×VDDIO	V
Sortie à niveau élevé	VOH	－	0.9×VDDIO	－	VDDIO	V
Sortie à bas niveau	VOL	－	0	－	0.1×VDDIO	V
Vérification de 50 % du courant de fonctionnement		VCC =14.5V	－	32	48	mA

Contrôleur de l’écran tactile FT6336U

Élément	Symbole	Condition	Min	Typ	Max	Unité
Supply Voltage	VDD		2.8	3.0	3.3	V
Tension d’alimentation élevée	VIH		0.7xVDD	－	VDD	V
Tension d’alimentation basse	VIL		-0.3	－	0.3xVDD	V
Tension de sortie élevée	VOH	IOH = -0.1mA	0.7xVDD	－	－	V
Tension de sortie basse	VOL	IOH = 0.1mA	－	－	0.3xVDD	V