- Spécifications Générales
- Fonction PIN sur l'interface
- Dessin Contour
- Autres Spécifications
- Description
- GUI Builder
| Article | Dimensions | Unité |
|---|---|---|
| Taille (diagonale) | 5.0 | pouces |
| Résolution matricielle | 800 × RGB × 480(TFT) | points |
| Contour du boîtier | NA | mm |
| Dimensions du module | 132.7(W) × 75.8(H) × 12.5(D) | mm |
| Surface de visée (VA) | 109.0(W) × 65.6 (H) | mm |
| Aire active (AA) | 108.0(W) × 64.8 (H) | mm |
| Espacement de point et de pixel | 0.135(H) × 0.135(V) | mm |
| Type LCD | TFT, Noir, Transmissif | |
| Direction de visée | 80/80/80/80 (IPS) | |
| Rapport longueur | 15:9 | |
| Carte de commande | Yes | |
| Interface (système) | UART | |
| Protocol | Proprietary UART + GPIO | |
| MCU | STM32F750 | |
| Points de détection | 1 | Points |
| Pavé tactile | Écran tactile à projection capacitive, PCAP | |
| Surface | Reflets | |
| Luminosité | 400 | cd/㎡ |
| Tension de fonctionnement | 5~28 | Vdc |
| Capacité de la mémoire flash | 16 | MB |
| Température de fonctionnement | -30~+80 | °C |
Définition CON2
| Pin | Symbole | Fonction | Remarque |
|---|---|---|---|
| 1 | VIN | Power supply 5V to 28V input | Input |
| 2 | GND | Power supply GND input | Input |
| 3 | Reserve | - | - |
| 4 | Reserve | - | - |
| 5 | GND | Power supply GND input | GND |
| 6 | GND | Power supply GND input | GND |
| 7 | Reserve | - | - |
| 8 | Reserve | - | - |
| 9 | VBUS | Power supply 5V input | Input |
| 10 | UART_RX | UART RX interface | I/O |
| 11 | UART_TX | UART TX interface | I/O |
| 12 | GND | Power supply GND input | Input |
| 13 | VIN | Power supply 5V to 28V input | Input |
| 14 | Reserve | - | - |
| 15 | Reserve | - | - |
| 16 | GND | Power supply GND input | Input |
CON3 Definition
| Pin | Symbole | Fonction | Remarque |
|---|---|---|---|
| 1 | +3V3 | 3.3V power for JTAG interface | Output |
| 2 | JTAG_SWCLK | CLK pin for JTAG interface | Input |
| 3 | GND | GND for JTAG interface | Output |
| 4 | JTAG_SWDIO | Data pin for JTAG interface | I/O |
| 5 | NRST | Reset pin for JTAG interface | Input |
| 6 | GND | GND | Output |
| 7 | WKUP | WKup,ADC,Timer,Event,I/O | TTL signal voltage is 3.3V |
| 8 | BOOT0 | Lo: Internal flash boot (Default) Hi: External flash boot |
TTL signal voltage is 3.3V |
| 9 | IO0 | ADC,DAC,Timer,Event,I/O | TTL signal voltage is 3.3V |
| 10 | IO1 | ADC,Timer,Event,I/O | TTL signal voltage is 3.3V |
| 11 | IO2 | ADC,Timer,Event,I/O | TTL signal voltage is 3.3V |
| 12 | IO3 | RST,Timer,Event,I/O | TTL signal voltage is 3.3V |
| 13 | IO4 | RST,Timer,Event,I/O | TTL signal voltage is 3.3V |
| 14 | IO5 | ADC,Timer,Event,I/O | TTL signal voltage is 3.3V |
| 15 | IO6 | RST,Timer,Event,I/O | TTL signal voltage is 3.3V |
| 16 | IO7 | RST,ADC,Event,I/O | TTL signal voltage is 3.3V |
Valeurs Nominales Maximales Absolues
| Article | Symbole | Valeur Min | Valeur Type | Valeur Max | Unité |
|---|---|---|---|---|---|
| Température Fonctionnement | TOP | -30 | － | +80 | ℃ |
| Température Stockage | TST | -30 | － | +80 | ℃ |
Caractéristiques Électroniques
| Article | Symbole | Valeur Min | Valeur Type | Valeur Max | Unité |
|---|---|---|---|---|---|
| Tension d'alimentation | VCC | 5 | 12 | 28 | V |
| Courant d'alimentation | ICC | 610 | 240 | 110 | mA |
| Tension broche I/O | -- | -- | -- | 3.3 | V |
BOM
| Article | Description |
|---|---|
| LCM | RFF500F-AWW-DNG |
| PCBA | SV10005R000FG00N0102 |
Nous fournissons également un ensemble de démonstration avec tous les accessoires nécessaires pour réaliser votre conception GUI sur les écrans.
1. Introduction of Raystar Smart Display GUI Builder
1-1 Dragging Widgets & preview function:
Users are able to design their screen appearance by dragging widgets on Raystar GUI Builder, and you also get a live preview of the changes. With the concept of "what you see is what you get", this function is time-saving for screen appearance design.
1-2 Simulator function:
There’s no need to purchase the hardware (Smart Display) to demonstrate the display effects and interactive behaviors. Users only need to use Raystar GUI Builder application software simulator to simulate the display effects and functions on the computer which greatly reduce costs and speed up project development.
1-3 Change or build GUI design on the client-side:
Instead of creating graphical objects through the Raystar engineering team, customers can replace or create GUI designs by themselves. But if customers have any other demands, we can also provide custom-design graphics objects.
1-4 How to get Raystar’s GUI Builder?
All you need is to contact us through our website or send inquiries to our sales email address. We'll provide it free of charge.
2.Smart Display GUI Builder introduction of operation and toolbar
2-1 The Start screen of Smart Display GUI Builder
2-2 The design page of Smart Display GUI Builder
2-3 Customization by Smart Display GUI Builder
2-4 Simulation by Smart Display GUI Builder
2-5 HW device update
2-6 The settings of installation
Install USB2CAN Driver:
*Execute stlink_winusb_install.bat (Please contact us to get the file)
Install Microsoft Visual C++ 2015-2019 Redistributable (x86)
*Execute VC_redist.x86.exe (Please contact us to get the file)
Install Smart Display GUI Builder
*Execute RaystarSmartDisplayGUIBuilderSetup_v0.1.5.msi (Please contact us to get the file)
*An icon of “Raystar SmartDisplay GUI Builder” will be shown after installing
