- Allgemeine Spezifikationen
- Schnittstelle Pin-Funktion
- Zeichnung
- Absolute Grenzwerte
- Elektrische Eigenschaften
| Artikel | Ausmaß | Einheit |
|---|---|---|
| Bauweise | COG | |
| Größe (Diagonale) | 2.42 | Zoll |
| Punktmatrix (Auflösung) | 128 × 64 | Punkte |
| Abmaße der modul | 66.8 × 41.3 × 3.71 | mm |
| Anzeigebereich (VA) | 56.01 × 28.49 | mm |
| Aktiver Bereich (AA) | 55.01 × 27.49 | mm |
| Emittierende Farbe | OLED, Weiß / Gelb / Grün / Himmelblau | |
| der Anzeigemodus | Passive Matrix | |
| IC | SSD1309 | |
| Schnittstelle | 8 Bits 6800 8000 / 4-Wire SPI / I2C | |
| PCAP IC | GT911 | |
| PCAP Schnittstelle | I2C | |
| Erkennungspunkte | 1 | Points |
| Touchscreen | kapazitiven Touchscreen | |
| Oberfläche | Glanz | |
| Stromversorgung | 3V | |
| Duty | 1/64 duty | |
| Betriebstemperatur | -20~+70 | °C |
| Lagertemperatur | -30~+80 | °C |
| Polarizer Type | Polarizer optional | |
| Typ | OLED-Grafikdisplay / OLED-Touchdisplay / OLED Anzeige / OLED-Display |
| Pin No. | Symbol | Funktion | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | NC(GND) | No connection | |||||||||||||||
| 2 | VSS | Ground. | |||||||||||||||
| 3-10 | NC | No connection | |||||||||||||||
| 11 | VDD | Power supply pin for core logic operation | |||||||||||||||
| 12 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
(1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
| 13 | BS2 | ||||||||||||||||
| 14 | NC | No connection | |||||||||||||||
| 15 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
|||||||||||||||
| 16 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
| 17 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
| 18 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 19 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 20~27 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
| 28 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. |
|||||||||||||||
| 29 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
| 30 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
| 31 | NC(GND) | No connection |
CTP-Pinbelegung
| No. | Symbol | Funktion |
|---|---|---|
| 1 | GND | Power ground |
| 2 | VDD | Power supply |
| 3 | INT | Interrupt signal, active low, asserted to request Host start a new transaction |
| 4 | SDA | I2C data signal |
| 5 | SCL | I2C clock signal |
| 6 | RST | External reset signal, active low |
| 7 | GND | Power ground |
| 8 | GND | Power ground |
| 9 | GND | Power ground |
| 10 | GND | Power ground |
Absolute Grenzwerte
| Parameter | Symbol | Mindestwert | Maximalwert | Einheit |
|---|---|---|---|---|
| Versorgungsspannung für Logik | VDD | -0.3 | 4 | V |
| Versorgungsspannung für Display | VCC | 0 | 15 | V |
| Betriebstemperatur | TOP | -20 | +70 | °C |
| Lagertemperatur | TSTG | -30 | +80 | °C |
Touchpanel-Controller GT911
| Parameter | Symbol | Mindestwert | Maximalwert | Einheit |
|---|---|---|---|---|
| Versorgungsspannung | VDD | 2.66 | 3.47 | V |
DC Elektrische Eigenschaften
| Artikel | Symbol | Bedingung | Mindestwert | typischer Wert | Maximalwert | Einheit |
|---|---|---|---|---|---|---|
| Versorgungsspannung für Logik | VDD | － | 2.8 | 3.0 | 3.3 | V |
| Versorgungsspannung für Display | VCC | － | 12.5 | 13.0 | 13.5 | V |
| Hochpegeleingang | VIH | － | 0.8×VDD | － | － | V |
| Niedrigpegeleingang | VIL | － | － | － | 0.2×VDD | V |
| Hochpegelausgang | VOH | － | 0.9×VDD | － | － | V |
| Niedrigpegelausgang | VOL | － | － | － | 0.1×VDD | V |
| 50% Check Board Operating Current | VCC =13.0V | － | 22 | 33 | mA | |
Touchpanel-Controller GT911
| Artikel | Symbol | Mindestwert | typischer Wert | Maximalwert | Einheit |
|---|---|---|---|---|---|
| Versorgungsspannung | VDD | 2.8 | 3.0 | 3.3 | V |
| Eingang Hochspannung | VIH | 0.75xVDD | VDD+0.3 | V | |
| Niedrige Eingangsspannung | VIL | -0.3 | － | 0.25xVDD | V |
| Ausgang Hochspannung | VOH | 0.85xVDD | － | － | V |
| Ausgang niedrige Spannung | VOL | － | － | 0.15xVDD | V |
