REX012864K - Raystar Optronics, Inc.

Modulo Display OLED Grafico COG 2,7 pollici 128x64 (IC SSD1309;Frame Opzione;FPC Opzione)

Model No. REX012864K

Il REX012864K è un modulo display OLED grafico COG da 2,7 pollici e 128×64, con opzione di cornice e opzioni FPC flessibili, tra cui ZIF e Hotbar FPC. Offre un’uscita monocromatica nitida con colori disponibili in bianco, giallo, verde e azzurro. Grazie al suo design sottile di 73.0 × 41.86 × 2.11 mm, questo modulo OLED è ideale per dispositivi portatili, pannelli di controllo e apparecchiature industriali.

Progettato per garantire affidabilità, il REX012864K funziona in un ampio intervallo di temperatura da -40°C a +80°C e supporta lo stoccaggio fino a +85°C. Il suo intervallo di tensione efficiente (2.8–3.3V logica, 12–14V display) assicura prestazioni stabili e durature. Questo versatile modulo OLED da 2,7 pollici rappresenta una soluzione resistente per diverse applicazioni embedded.

Per supporto tecnico o preventivi relativi al REX012864K o ad altri moduli OLED da 2,7 pollici, non esitate a contattare il nostro team commerciale.

Fonte dati: REX012864KYAP3N00000

AGGIUNGI ALLA RICHIESTA/Demo Code

SCARICA PDF

Indietro

Articolo	Dimensioni	Unità
Struttura	COG; Frame Opzione
Dimensione (Diagonale)	2.7	pollici
A matrice di punti (Risoluzione)	128 × 64	punti
Dimensione del modulo	73.0 × 41.86 × 2.11	mm
Area di visualizzazione (VA)	63.41 × 32.69	mm
Area attiva (AA)	61.41 × 30.69	mm
Dimensioni del Dot	0.45 × 0.45	mm
Passo del Dot	0.48 × 0.48	mm
Colore di emissione	OLED, Bianco / Giallo / Verde / Cielo blu
Modalità display	Matrice passiva
IC	SSD1309
Interfaccia	8080 / 6800 / SPI / I2C
Alimentatore	3V
Duty	1/64 duty
Temperatura di lavoro	-40~+80	°C
Temperatura di stock	-40~+85	°C
Polarizer Type	polarizzatore opzionale
FPC Options	Yes
Type	Modulo display OLED grafico

Pin No.

Simbolo

Descrizione

NC(GND)

No Connection

VSS

Ground.

3~10

No connection

VDD

Power supply pin for core logic operation

BS1

MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select.

	BS1	BS2
I2C	1	0
4-wire Serial	0	0
8-bit 68XX Parallel	0	1
8-bit 80XX Parallel	1	1

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD

BS2

No connection

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

RES#

This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.

D/C#

This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS.

R/W#

This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

E/RD#

This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

20~27

D0~D7

These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout,SDAin in application and D0 is the serial clock input, SCL.

IREF

This pin is the segment output current reference pin.
IREF is supplied externally.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin.

NC(GND)

No connection

Modulo Display OLED Grafico COG 2,7 pollici 128x64 (IC SSD1309;Frame Opzione;FPC Opzione) - REX012864K Disegno

Parametro	Simbolo	Valore Min	Valore massimo	Unità
Tensione di alimentazione per logica	VDD	-0.3	4	V
Tensione di alimentazione per display	VCC	0	15	V
Temperatura di lavoro	TOP	-40	+80	°C
Temperatura di stock	TSTG	-40	+85	°C

Articolo	Simbolo	Condizioni	Valore Min	Valore tipico	Valore massimo	Unità
Tensione di alimentazione per logica	VDD	-	2.8	3.0	3.3	V
Tensione di alimentazione per display	VCC	-	12	13	14	V
Ingresso Alto Livello	VIH	-	0.8×VDD	-	-	V
Ingresso Basso Livello	VIL	-	-	-	0.2×VDD	V
Uscita Alto Livello	VOH	-	0.9×VDD	-	-	V
Uscita Basso Livello	VOL	-	-	-	0.1×VDD	V
50% Check Board Operating Current		VCC =13.0V	-	22	33	mA

Frame Opzione

Drawing	Material	FR No.	Detailed Drawing	Create Date
	SUS-304	FFL60128640A221XXX00	View	20120131

FPC Opzione

FPC Length	PIN	pitch	ZIF / HOTBAR FPC	Interface	FPC No.	Create Date
36	31	0.5	ZIF	6800, 8080, SPI, I2C	FPC2050003111XXXXX01	20140923
69.85	22	0.5	ZIF	6800, 8080, SPI, I2C	FPC2050002211XXXXX03	20161207
105.57	30	0.5	ZIF	6800, 8080, SPI, I2C	FPC2050003011XXXXX11	20170406
42	24	0.5	ZIF	6800, 8080, SPI, I2C	FPC2050002411XXXXX11	20191218