1.1 吋 96x64 繪圖型 OLED 顯示器模組具彈性 FPC 選擇（SSD1327 IC） - REX009664B
1.1 吋 96x64 繪圖型 OLED 顯示器模組具彈性 FPC 選擇（SSD1327 IC） - REX009664B
1.1 吋 96x64 繪圖型 OLED 顯示器模組具彈性 FPC 選擇（SSD1327 IC） - REX009664B
1.1 吋 96x64 繪圖型 OLED 顯示器模組具彈性 FPC 選擇（SSD1327 IC） - REX009664B
1.1 吋 96x64 繪圖型 OLED 顯示器模組具彈性 FPC 選擇（SSD1327 IC） - REX009664B
1.1 吋 96x64 繪圖型 OLED 顯示器模組具彈性 FPC 選擇（SSD1327 IC） - REX009664B

1.1 吋 96x64 繪圖型 OLED 顯示器模組具彈性 FPC 選擇（SSD1327 IC）

Model No. REX009664B

REX009664B 是一款 1.1 吋OLED 顯示器模組，解析度為 96x64。支援灰階功能，並預設搭載 4-wire SPI 介面，亦可選擇 I2C、6800 或 8080 介面，以提升系統整合的彈性。此款 OLED 模組尺寸為 29×22.5 mm，採用 SSD1327 IC，並支援多種彈性 FPC 配置，包括 ZIF 與 Hotbar 等選項，發光顏色則提供白光與黃光。

為追求優異的視覺表現，96x64 OLED 面板提供高達 10,000:1 的對比度，影像清晰鮮明。其邏輯工作電壓範圍為 2.8V 至 3.3V（典型值為 3.0V），具備低功耗特性。此模組專為嚴苛環境設計，工作溫度範圍可達 -40°C 至 +80°C，儲存溫度上限為 +85°C，展現出極佳的穩定性與耐用性。

★ 可選配其他 FPC 規格

資料來源：REX009664BYAP3N00H00

產品詢問 規格書下載 規格書下載 回上頁 上一個產品 下一個產品
  • 一般規格
  • Pin功能定義
  • 規格圖
  • 最大絕對額定值
  • 電氣特性
  • 選項
項目 規格內容 單位
結構 COG
對角線尺寸 1.1 吋
點陣/解析度 96 × 64 dots
模組尺寸 29.00 × 22.50 × 1.65 mm
可視區域(VA) 24.54 × 17.02 mm
有效區域(AA) 22.53 × 15.01 mm
點(像素)大小 0.205 × 0.205 mm
點(像素)間距 0.235 × 0.235 mm
發光色 OLED, 白色 / 黃色
支援灰階 有
顯示模式 被動矩陣（Passive Matrix）
IC SSD1327
介面 4-wire SPI, I2C, 8-bit 6800, 8-bit 8080
電源電壓 3V
驅動方式(Duty) 1/64 Duty
工作溫度 -40~+80 °C
儲存溫度 -40~+85 °C
可選FPC 是
類型 繪圖型OLED顯示器
Pin No. 符號 功能說明
1 VSS Ground pin. It must be connected to external ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select.
Bus Interface selection
BS[2:1] 介面
00 4 line SPI
01 I2C
11 8-bit 8080 parallel
10 8-bit 6800 parallel
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
7 BS2
8 VSS Ground pin. It must be connected to external ground.
9 IREF This pin is the segment output current reference pin
10 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
11 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
12 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
13 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.

14		 E This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is
selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
16 D1
17 D2
18 D3
19 D4
20 D5
21 D6
22 D7
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
24 VSS Ground pin.

REX009664B (HOTBAR FPC)

1.1 吋 96x64 繪圖型 OLED 顯示器模組 (Hotbar FPC) -REX009664B 規格圖

 

REX009664B (ZIF FPC)

1.1 吋 96x64 繪圖型 OLED 顯示器模組 (ZIF FPC)-REX009664B 規格圖

參數 符號 最小值 最大值 單位
工作電源電壓 VCI -0.3 4.0 V
邏輯電源電壓 VDD -0.5 2.75 V
顯示電源電壓 VCC -0.5 19.0 V
工作溫度 TOP -40 +80 °C
儲存溫度 TSTG -40 +85 °C

DC 電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VCI － 2.8 3.0 3.3 V
顯示電源電壓 VCC － 8.0 8.5 9.0 V
輸入高電壓 VIH － 0.8×VCI － VCI V
輸入低電壓 VIL － VSS － 0.2×VCI V
輸出高電壓 VOH － 0.9×VCI － VCI V
輸出低電壓 VOL － VSS － 0.1×VCI V
50%顯示畫面耗電流 ICC VCC=8.5V － 13.0 26.0 mA

可選FPC

圖示 FPC 長度 PIN Pitch ZIF FPC / HOTBAR FPC 介面 FPC No. 建立日期
FPC2050002411XXXXX02_REX009664B 25.05 24 0.5 ZIF FPC  4-Wire SPI, I2C, 6800, 8080 FPC2050002411XXXXX02 20170602
FPC2070002401XXXXX00_REX009664B 17.8 24 0.7 HOTBAR 4-Wire SPI, I2C, 6800, 8080 FPC2070002401XXXXX00 20171222

相關產品

Top