0.95 吋 96x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX009664D
0.95 吋 96x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX009664D
0.95 吋 96x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX009664D
0.95 吋 96x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX009664D

0.95 吋 96x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）

Model No. REX009664D

REX009664D 是一款 0.95 吋被動矩陣 OLED 顯示器模組，採用 COG（Chip-on-Glass）結構設計，具備 96×64 解析度，模組尺寸為 24.9 × 22.95 × 1.61 mm。

本模組支援多種介面，包括 6800、8080、4-wire SPI 和 I2C。搭載 SSD1305 控制 IC，並採用 1/64 duty 驅動設計。REX009664D 非常適合應用於智慧家電、工業手持設備及醫療裝置等場景。

REX009664D 支援 -40°C 至 +80°C 的廣溫操作溫度範圍，邏輯電壓（VDD）介於 2.4V 至 3.3V，常見操作電流約為 6–9 mA（以 50%顯示畫面耗電流為基準）。

若您需要 REX009664D 或其他 0.95 吋 OLED 顯示器模組的技術支援或報價，歡迎聯繫我們的業務團隊！

資料來源：REX009664DYPP3N00000

產品詢問 規格書下載 回上頁 上一個產品 下一個產品
  • 一般規格
  • Pin 功能定義
  • 規格圖
  • 最大絕對額定值
  • 電氣特性
項目 規格內容 單位
結構 COG
對角線尺寸 0.95 吋
點陣/解析度 96 × 64 dots
模組尺寸 24.9 × 22.95 × 1.61 mm
可視區域(VA) 21.953 × 15.424 mm
有效區域(AA) 19.946 × 13.418 mm
點(像素)大小 0.184 × 0.186 mm
點(像素)間距 0.208 × 0.21 mm
發光色 OLED, 白色 / 黃色
顯示模式 被動矩陣（Passive Matrix）
IC SSD1315
介面 6800 / 8080 / 4-wire SPI / I2C
電源電壓 3V
驅動方式(Duty) 1/64 Duty
工作溫度 -40~+80 °C
儲存溫度 -40~+85 °C
偏光片類型(Polarizer Type) 可選偏光鏡
類型 繪圖型OLED顯示器
Pin No. 符號 功能說明
1 NC No connection
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
3 VSS Ground pin. It must be connected to external ground.
4 NC No connection
5 VDD Power supply pin for core logic operation.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 are pin select
BS[2:1] Interface
00 4 line SPI
01 I2C
11 8-bit 8080 parallel
10 8-bit 6800 parallel
Note
(1) 0 is connected to VSS (2) 1 is connected to VDD
7 BS2
8 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
9 RES# This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
10 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection.
11 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
12 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
13 D0 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
14 D1
15 D2
16 D3
17 D4
18 D5
19 D6
20 D7
21 IREF This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA.
22 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
24 VLSS This is an analog ground pin. It should be connected to VSS externally.
25 NC No connection

0.95 吋 96x64 COG 繪圖型 OLED 顯示器模組（SSD1315 IC）- REX009664D 規格圖

參數 符號 最小值 典型值 最大值 單位
邏輯電源電壓 VDD -0.3 － 4.0 V
顯示電源電壓 VCC 0 － 18.0 V
操作溫度 TOP -40 － +80 °C
儲存溫度 TSTG -40 － +85 °C

DC 電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VDD － 1.65 3.0 3.3 V
顯示電源電壓 VCC － 7.5 12.0 12.5 V
輸入高準位 VIH － 0.8×VDD － VDD V
輸入低準位 VIL － 0 － 0.2×VDD V
輸出高準位 VOH Iout = 100uA 0.9×VDD － VDD V
輸出低準位 VOL Iout = 100uA 0 － 0.1×VDD V
顯示 50% 像素 ICC － － 6 9 mA

相關產品

Top