2.55 吋 206x36 COG 繪圖型 OLED 顯示器搭載SSD1362 - REX020636A
2.55 吋 206x36 COG 繪圖型 OLED 顯示器搭載SSD1362 - REX020636A
2.55 吋 206x36 COG 繪圖型 OLED 顯示器搭載SSD1362 - REX020636A
2.55 吋 206x36 COG 繪圖型 OLED 顯示器搭載SSD1362 - REX020636A
2.55 吋 206x36 COG 繪圖型 OLED 顯示器搭載SSD1362 - REX020636A

2.55 吋 206x36 COG 繪圖型 OLED 顯示器搭載SSD1362

Model No. REX020636A

REX020636A 是一款 2.55 吋 206x36 繪圖型 COG OLED 顯示器模組，有效顯示區域的對角尺寸為 2.55 吋，模組尺寸為 70.77x15.14 mm。此 OLED 顯示器模組使用 SSD1362 IC，支援 3-Wire SPI、4-Wire SPI 和 I2C 介面及4-bit 灰階。REX020636A 是曜凌光電首款 2.55 吋 OLED 標準品，擁有 206x36 dots 的解析度和高亮度 (典型值為 280 nits)，為客戶提供了不同與以往市場上常見OLED型號顯示器體驗。

此OLED 模組具有 10,000:1 的高對比度，邏輯供電電壓範圍為 1.65V 到 2.6V，工作溫度範圍為 -40℃ 到 +80℃，存儲溫度範圍為 -40℃ 到 +85℃。REX012832R 的發光顏色為白色。

Data source of: REX020636AWAP3N00000

產品詢問 規格書下載 回上頁 上一個產品 下一個產品
  • 一般規格
  • Pin功能定義
  • 規格圖
  • 最大絕對額定值
  • 電氣特性
項目 規格內容 單位
結構 COG
對角線尺寸 2.55 吋
點陣/解析度 206 × 36 dots
模組尺寸 70.77 × 15.14 × 2.01 mm
可視區域(VA) 64.84 × 12.14 mm
有效區域(AA) 63.84 × 11.14 mm
點(像素)大小 0.29 × 0.29 mm
點(像素)間距 0.31 × 0.31 mm
發光色 OLED, 白色
支援灰階 有
顯示模式 被動矩陣 (Passive Matrix)
灰階 4-bit
IC SSD1362
介面 3-Wire SPI, 4-Wire SPI, I2C
電源電壓 3V
驅動方式(Duty) 1/36 Duty
工作溫度 -40~+80 °C
儲存溫度 -40~+85 °C
類型 繪圖型OLED顯示器
No. 符號 功能說明
1 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
2 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
3 VP This pin is the segment pre-charge voltage reference pin.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
4 VSL This is a reserved pin. It should be connected to VLSS externally.
5 VLSS Analog system ground pin. It must be connected to external ground.
6 VDD VDD can be supplied externally (within the range of 1.65V to 2.6V) or regulated internally from VCI when VCI is >2.6V.A capacitor should be connected between VDD and VSS under all circumstances.
7 VCI Low voltage power supply.
VCI must always be equal to or higher than VDD and VDDIO.
8 VDDIO Power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
9 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled Low (active Low).In I2C mode, this pin must be connected to VSS.
10 RES# This pin is reset signal input.
When the pin is pulled Low, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
11 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data will be interpreted as data.
When the pin is pulled LOW, the data will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
12 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie Low. When serial interface mode is selected,D0 will be the serial clock input: SCLK;D1 will be the serial data input: SID. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
13 D1
14 D2
15 BS0 MCU bus interface selection pins.
BS[1:0] Interface
00 4-Wire SPI
01 3-Wire SPI
10 I2C
16 BS1
17 VSS Ground pin.
18 IREF When external IREF is used, a resistor should be connected between this pin and VSS to maintain current of around 18.75uA.
When internal IREF is used, this pin should be kept NC.
19~20 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.

2.55 吋 206x36 COG 繪圖型 OLED 顯示器搭載SSD1362 - REX020636A

參數 符號 最小值 最大值 單位
電源電壓 VDD -0.5 2.75 V
電源電壓 VCI -0.3 5.5 V
電源電壓 VDDIO -0.5 5.5 V
電源電壓 VCC 7 21 V
工作溫度 TOP -40 +80 °C
儲存溫度 TSTG -40 +85 °C

DC 電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
顯示電源電壓 VCC － 10.0 12.0 12.5 V
低壓電源 VCI － 1.65 － 3.5 V
輸入 / 輸出 Pin 電源 VDDIO － 1.65 － VCI V
邏輯電源電壓 VDD － 1.65 － 2.6 V
輸入高準位 VIH － 0.8×VDDIO － － V
輸入低準位 VIL － － － 0.2×VDDIO V
輸出高準位 VOH － 0.9×VDDIO － － V
輸出低準位 VOL － － － 0.1×VDDIO V
Display 50% Pixel on ICC VCC =12V － 25 35 mA

相關產品

Top