1.54 吋 160x80 繪圖型 COG OLED 顯示器搭載 SSD1320 - REX016080A
1.54 吋 160x80 繪圖型 COG OLED 顯示器搭載 SSD1320 - REX016080A
1.54 吋 160x80 繪圖型 COG OLED 顯示器搭載 SSD1320 - REX016080A
1.54 吋 160x80 繪圖型 COG OLED 顯示器搭載 SSD1320 - REX016080A
1.54 吋 160x80 繪圖型 COG OLED 顯示器搭載 SSD1320 - REX016080A

1.54 吋 160x80 繪圖型 COG OLED 顯示器搭載 SSD1320

Model No. REX016080A

REX016080A 是一款採用 SSD1320 IC 的 160x80 繪圖型 COG OLED 模組，有效區域對角線尺寸為 1.54 吋，模組尺寸為 35.02x17.50 mm。此 OLED 模組配有內建 SSD1320 IC，並支持 6800、8080、4 線 SPI 和 I2C 介面，以及 4-bit 灰階，可廣泛應用於智慧家電、電競鍵盤/方向盤、網通產品、智能檢測/手錶、智能醫療設備等產品應用。

REX012832R OLED 模組有白色可選擇。模組邏輯供電電壓範圍為 1.65V 到 3.3V，典型值為 3.0V，並具有 10,000:1 的高對比度，操作溫度範圍為 -40℃ 到 +80℃，儲存溫度範圍為 -40℃ 到 +85℃。

Data source ref: REX016080AWPP3N00000

產品詢問 規格書下載 回上頁 上一個產品 下一個產品
  • 一般規格
  • Pin功能定義
  • 規格圖
  • 最大絕對額定值
  • 電氣特性
項目 規格內容 單位
結構 COG
對角線尺寸 1.54 吋
點陣/解析度 160 × 80 dots
模組尺寸 43.5 × 22.5 × 1.41 mm
可視區域(VA) 37.02 × 19.50 mm
有效區域(AA) 35.02 × 17.50 mm
點(像素)大小 0.199 × 0.199 mm
點(像素)間距 0.219 × 0.219 mm
發光色 OLED, 白色
支援灰階 有
顯示模式 被動矩陣 (Passive Matrix)
灰階 4-bit
IC SSD1320
介面 6800, 8080, 4-Wire SPI, I2C
電源電壓 3V
驅動方式(Duty) 1/80 Duty
工作溫度 -40~+80 °C
儲存溫度 -40~+85 °C
類型 繪圖型OLED顯示器
No. 符號 功能說明
1 N.C.
(GND)		 Reserved Pin (Supporting Pin)
The supporting pin can reduce the influences from stresses on the function pins.
This pin could be connected to external ground as the ESD protection circuit.
2 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. It must be connected to external source.
3~4 N.C. Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
5 BS1 Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
  BS1 BS2
I2C 1 0
4-wire SPI 0 0
8-bit 68XX Parallel 0 1
8-bit 80XX Parallel 1 1
6 BS2
7 VSS Ground of Logic Circuit
This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground.
8 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current at 10μA maximum.
9 CS# Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
10 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin pull high during normal operation.
11 D/C# Data/Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at
D7~D0 is treated as display data. When the pin is pulled low, the input at
D7~D0 will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
12 R/W# Read/Write Select or Write
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as
Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input.
Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
13 E/RD# Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the
Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
14 D0 Host Data Input/Output Bus
These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D2, D1 should be tied together as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout,
SDAin in application and D0 is the serial clock input, SCL.
15 D1
16 D2
17 D3
18 D4
19 D5
20 D6
21 D7
22 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
23 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A tantalum capacitor should be connected between this pin and VSS.
24 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. It must be connected to external source.

1.54 吋 160x80 繪圖型 COG OLED 顯示器搭載 SSD1320 - REX016080A

參數 符號 最小值 典型值 最大值 單位
Supply Voltage for Logic VDD -0.3 － 4 V
Supply Voltage for Display VCC 0 － 19 V
Operating Temperature TOP -40 － +80 °C
Storage Temperature TSTG -40 － +85 °C

DC 電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VDD － 1.65 3.0 3.3 V
顯示電源電壓 VCC － 8.0 15.0 15.5 V
輸入高準位 VIH － 0.8×VDD － VDD V
輸入低準位/td> VIL － 0 － 0.2×VDD V
輸出高準位 VOH － 0.9×VDD － VDD V
輸出低準位 VOL － 0 － 0.1×VDD V
VCC 供電電流 ICC VDD=3V,VCC=15V
Display 50% Pixel ON		 － 14 21 mA

相關產品

Top