REX012864AC - Raystar Optronics, Inc.

Modules d’affichage OLED Graphique COG 0,96 pouces 128x64 (IC SSD1315)

Model No. REX012864AC

Le REX012864AC est un module d’affichage OLED graphique à matrice passive COG de 0,96 po et 128×64, intégrant le circuit de commande SSD1315. Le module mesure 26,70 × 19,26 × 1,26 mm, avec une zone active de 21,74 × 10,86 mm, et prend en charge les interfaces 6800, 8080, SPI et I2C. Nos modules OLED avec interface I2C offrent une solution de communication compacte, écoénergétique et économique, idéale pour les applications intégrées où l’espace est restreint.

Conçu pour la fiabilité, le REX012864AC fonctionne dans des environnements extrêmes de -40°C à +80°C et peut être entreposé à des températures allant de -40°C à +85°C. Le module prend en charge une tension d’alimentation logique allant jusqu’à 4,0V et une tension d’alimentation de l’affichage allant jusqu’à 18,0V. Que ce soit pour le contrôle industriel, l’instrumentation portable ou l’électronique extérieure, ce module OLED offre durabilité et haute qualité visuelle.

Pour obtenir un soutien technique ou une soumission pour le REX012864AC ou d’autres modules d’affichage OLED I2C 128×64, n’hésitez pas à communiquer avec notre équipe des ventes.

Data source ref: REX012864ACWPP3N00000

Ajouter à demande / Demo Code

Téléchargement PDF

Retour

Article	Dimensions	Unité
Structure	COG
Taille (diagonale)	0.96	pouces
Résolution matricielle	128 × 64	points
Dimensions du module	26.7 × 19.26 × 1.26	mm
Surface de visée (VA)	23.94 × 12.09	mm
Aire active (AA)	21.74 × 10.86	mm
Taille de point et de pixel	0.15 × 0.15	mm
Espacement de point et de pixel	0.17 × 0.17	mm
Couleur émise	OLED, Blanc / Jaune
Mode d’affichage	Matrice passive
IC	SSD1315
Interface	8080 / 6800 / SPI / I2C
Tension d’alimentation	3V
Duty	1/64 cycle de service
Température de fonctionnement	-40~+80	°C
Température de rangement	-40~+85	°C
Type de polariseur	Polariseur optionnel
Type	Affichage OLED graphiques

Pin No.

Symbole

Fonction

N.C. (GND)

The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

C2N

C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.

C2P

C1P

C1N

VBAT

This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.

VSS

Ground pin. It must be connected to external ground.

VDD

Power supply pin for core logic operation.

BS0

These pins are MCU interface selection input. See the
following table:

	BS0	BS1	BS2
I2C	0	1	0
3-wire SPI	1	0	0
4-wire SPI	0	0	0
8-bit 68XX Parallel	0	0	1
8-bit 80XX Parallel	0	1	1

BS1

BS2

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

RES#

This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.

D/C#

This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDD), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams of IC SPEC.

R/W#

This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

E/RD#

When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDD) and the chip is selected.
When connecting to an 8080-series microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

18~25

D0~D7

These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.

IREF

When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.

VCOMH

The pin for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.

VLSS

This is an analog ground pin. It should be connected to VSS externally.

NC
(GND)

The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

Modules d’affichage OLED Graphique COG 0,96 pouces 128x64 (IC SSD1315) - REX012864AC Dessin de contour

Paramètre	Symbole	Min	Max	Unité
Tension d’alimentation pour le circuit logique	VDD	0	4.0	V
Charge Pump Regulator Supply Voltage	VBAT	0	6.0	V
Tension d’alimentation pour l’affichage	VCC	0	15.0	V
Température de fonctionnement	TOP	-40	+80	°C
Température de rangement	TSTG	-40	+85	°C

DC Paramètres électriques

Élément	Symbole	Condition	Min	Typ	Max	Unité
Tension d’alimentation pour le circuit logique	VDD	－	1.65	3.0	3.3	V
Charge Pump Regulator Supply Voltage	VBAT	－	2.4	3.5	5.0	V
Tension d’alimentation pour l’affichage	VCC	－	6.0	12.0	12.5	V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC)	Charge Pump VPP	－	7.0	7.5	－	V
Tension d’alimentation élevée	VIH	－	0.8xVDD	－	VDD	V
Tension d’alimentation élevée	VIL	－	0	－	0.2xVDD	V
Tension de sortie élevée	VOH	－	0.9xVDD	－	VDD	V
Tension de sortie basse	VOL	－	0	－	0.1xVDD	V
Operating Current for VCC (50% display ON) (VCC Supplied Externally)	ICC	VCC=12V	－	10	20	mA
Vérification de 50 % du courant de fonctionnement (VCC Generated by Internal DC/DC)	IBAT	－	－	15	30	mA