2,23 Zoll 128x64 COG OLED-Grafikdisplay (SH1106 IC) - REX012864AH
2,23 Zoll 128x64 COG OLED-Grafikdisplay (SH1106 IC) - REX012864AH
2,23 Zoll 128x64 COG OLED-Grafikdisplay (SH1106 IC) - REX012864AH
2,23 Zoll 128x64 COG OLED-Grafikdisplay (SH1106 IC) - REX012864AH
2,23 Zoll 128x64 COG OLED-Grafikdisplay (SH1106 IC) - REX012864AH

1,54 Zoll 128x64 COG OLED-Grafikdisplay (SH1106 IC)

Model No. REX012864AH

Das REX012864AH ist ein COG-Grafik-OLED-Displaymodul mit einer Auflösung von 128x64. Dieses monochrome Grafikdisplay ist mit einem SH1106-IC ausgestattet und kann über die I2C-, 4-Leiter-SPI-, 6800- oder 8080-Parallel-Schnittstelle kommunizieren. Das Modul hat eine Abmessung von 42,04 x 27,22 mm und eine aktive Fläche (AA) von 35,05 x 17,51 mm. Es zeichnet sich durch ein hohes Kontrastverhältnis von 10.000:1, eine 3V-Stromversorgung und einen 1/64-Duty-Cycle aus. Die Vielzahl der Schnittstellenoptionen macht diese OLED-Module anpassungsfähig an jedes Projekt oder jede Anwendung.

Das REX012864AH ist ideal für Smart-Home-Anwendungen, POS-Systeme, intelligente Technologiegeräte, Energiesysteme, Kommunikationssysteme, medizinische Instrumente usw. Dieses Modul kann bei Temperaturen von -40°C bis +80°C betrieben werden; seine Lagertemperaturen reichen von -40°C bis +85°C.

Datenquelle-Referenz：REX012864AHWPP3N00000

Zu Anfrage hinzufügen/Demo Code PDF-Download zurück Zurück Weiter
  • Allgemeine
  • Schnittstelle Pin-Funktion
  • Zeichnung
  • Absolute Maximum Ratings
  • Electrical Characteristics
Artikel Ausmaß Einheit
Bauweise COG
Größe (Diagonale) 1.54 Zoll
Punktmatrix (Auflösung) 128 × 64 Punkte
Abmaße der modul 42.04 × 27.22 × 1.41 mm
Anzeigebereich (VA) 37.05 × 19.51 mm
Aktiver Bereich (AA) 35.05 × 17.51 mm
Punktgröße 0.249 × 0.249 mm
Punktabstand 0.274 × 0.274 mm
Emittierende Farbe Weiß / Gelb
der Anzeigemodus Passive Matrix
IC SH1106
Schnittstelle 6800,8080,4-Wire SPI,I2C
Stromversorgung 3V
Duty 1/64 duty
Betriebstemperatur -40~+80 °C
Lagertemperatur -40~+85 °C
Typ OLED-Grafikdisplay / OLED Anzeige / OLED-Display
No. Symbol Beschreibung
1 ESD_GND ESD Ground pin 
2 VSS Ground.
3 VSS Ground.
4 NC No connection
5 VDD1 Power supply input
6 IM1 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI
IM1 1 1 0 0
IM2 1 0 1 0
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD1
7 IM2
8 CS# This pad is the chip select input. When CS# = "L", then the chip select becomes active, and data/command I/O is enabled.
9 RES# This is a reset signal input pad. When RES# is set to "L", the settings are initialized. The reset operation is performed by the RES# signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = "H"：the inputs at D0 to D7 are treated as display data.
A0 = "L"： the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 WR#
(R/W#)		 This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR# signal. The signals on the data bus are latched at the rising edge of the WR# signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W#="H": Read.
When R/W#="L": Write.
12 E/RD# This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD# signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD# ="H": Enable.
When RD# ="L": Disable.
13-20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
21 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
22 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
23 VPP OLED panel power supply. It could be supplied externally.
A capacitor should be connected between this pad and VSS.
24 ESD_GND ESD Ground pin 

2,23 Zoll 128x64 COG OLED-Grafikdisplay (SH1106 IC) - REX012864AH

Parameter Symbol Mindestwert Maximalwert Einheit
Tensión de Alimentación para Lógica VDD -0.3 3.6 V
Versorgungsspannung für Display VCC -0.3 14.5 V
Température de fonctionnement TOP -40 +80 °C
Température de rangement TSTG -40 +85 °C

DC Electrical Characteristics

Artikel Symbol Betriebsbedingungen Mindestwert typischer Wert Maximalwert Einheit
Tensión de Alimentación para Lógica VDD1 － 1.65 3.0 3.3 V
Versorgungsspannung für Display VPP － 6.4 12.5 13.0 V
High Level Input VIH － 0.8×VDD1 － VDD1 V
Low Level Input VIL － VSS － 0.2×VDD1 V
High Level Output VOH － 0.8×VDD1 － VDD1 V
Low Level Output VOL － VSS － 0.2×VDD1 V
Display 50% Pixel on IPP VPP =12.5V － 13 20 mA

Related Products

Top