Display Touchscreen OLED COG+PCB da 2,42 pollici, 128x64 punti - REX012864J-CTP
Display Touchscreen OLED COG+PCB da 2,42 pollici, 128x64 punti - REX012864J-CTP
Display Touchscreen OLED COG+PCB da 2,42 pollici, 128x64 punti - REX012864J-CTP
Display Touchscreen OLED COG+PCB da 2,42 pollici, 128x64 punti - REX012864J-CTP
Display Touchscreen OLED COG+PCB da 2,42 pollici, 128x64 punti - REX012864J-CTP
  • Specifiche generali
  • Funzione dei Pin di Interfaccia
  • Disegno
  • Valori massimi assoluti
  • Caratteristiche elettriche
Articolo Dimensioni Unità
Struttura COG+PCB
Dimensione (Diagonale) 2.42 pollici
A matrice di punti (Risoluzione) 128 × 64 punti
Dimensione del modulo 75.0 × 52.7 × 10.2 (MAX) mm
Area di visualizzazione (VA) 57.01 × 29.49 mm
Area attiva (AA) 55.01 × 27.49 mm
Dimensioni del Dot 0.40 × 0.40 mm
Passo del Dot 0.43 × 0.43 mm
Colore di emissione OLED, Bianco / Giallo / Verde / Cielo blu
Modalità display Matrice passiva
IC SSD1309
Interfaccia 8080 option 6800, 4-SPI, I2C
PCAP IC GT911
PCAP Interfaccia I2C
Punti di rilevamento 1 Points
Touch Screen touchscreen capacitivo
Superficie Bagliore (Glare)
Alimentatore 3V
Duty 1/64 duty
Temperatura di lavoro -20~+70 °C
Temperatura di stock -30~+80 °C
Polarizer Type polarizzatore opzionale
Type Modulo display OLED grafico,Touchscreen capacitivo OLED
No. Simbolo Funzione
1 VDD Power supply pin for core logic operation
2 VSS Ground.
3 NC(GND) No connection
4~11 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
12 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
13 NC(GND) No connection
14 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
15 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
16 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
17 E This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
18 NC(GND) No connection
19 DISP No Connection
20 NC(GND) No connection
21 TP_INT Interrupt signal, active low, asserted to request
Host start a new transaction
22 TP_SDA I2C data signal
23 TP_SCL I2C clock signal
24 TP_RST External reset signal, active low

Display Touchscreen OLED COG+PCB da 2,42 pollici, 128x64 punti - REX012864J-CTP

Parametro Simbolo Valore Min Valore massimo Unità
Supply Voltage for Logic VDD -0.3 4 V
Temperatura di lavoro TOP -20 +70 °C
Temperatura di stock TSTG -30 +80 °C

DC Caratteristiche elettriche

Articolo Simbolo Condizione Valore Min Valore tipico Valore massimo Unità
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current IDD VDD =3V - 150 300 mA
Top