- Specifiche generali
- Funzione dei Pin di Interfaccia
- Disegno
- Valori massimi assoluti
- Caratteristiche elettriche
| Articolo | Dimensioni | Unità |
|---|---|---|
| Struttura | COG | |
| Dimensione (Diagonale) | 1.18 | pollici |
| A matrice di punti (Risoluzione) | 128 × 128 | punti |
| Dimensione del modulo | Ø50.5 × 5.0 | mm |
| Area di visualizzazione (VA) | Ø31.0 | mm |
| Area attiva (AA) | Ø30.0 | mm |
| Dimensioni del Dot | 0.210 × 0.210 | mm |
| Passo del Dot | 0.235 × 0.235 | mm |
| Colore di emissione | OLED, Bianco / Giallo | |
| Supporto scala di grigi | Yes | |
| Modalità display | Matrice passiva | |
| Scala di grigi | 4 bits | |
| IC | SSD1327 | |
| Interfaccia | 4-line SPI / I2C | |
| PCAP IC | FT3268 | |
| PCAP Interfaccia | I2C | |
| Punti di rilevamento | 1 | Points |
| Touch Screen | touchscreen capacitivo | |
| Alimentatore | 3V | |
| Duty | 1/128 duty | |
| Temperatura di lavoro | -20~+70 | °C |
| Temperatura di stock | -30~+70 | °C |
| Polarizer Type | polarizzatore opzionale | |
| Type | Modulo display OLED grafico,Touchscreen capacitivo OLED |
| Pin No. | Simbolo | Funzione | ||||||
|---|---|---|---|---|---|---|---|---|
| 1 | VSS | Ground pin. It must be connected to external ground. | ||||||
| 2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||
| 3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||
| 4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||
| 5 | VDD | Power supply pin for core logic operation. VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances. |
||||||
| 6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select. Bus Interface selection
|
||||||
| 7 | IREF | This pin is the segment output current reference pin | ||||||
| 8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||
| 9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||
| 10 | DC# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, will be interpreted as data. When the pin is pulled LOW, will be transferred to a command register In I2C mode, this pin acts as SA0 for slave address selection. |
||||||
| 11 | D0 | When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL. |
||||||
| 12 | D1 | |||||||
| 13 | D2 | |||||||
| 14 | TP_SCK | I2C clock signal | ||||||
| 15 | TP_SDA | I2C data signal | ||||||
| 16 | TP_INT | Interrupt signal | ||||||
| 17 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | ||||||
| 18 | VSS | Ground |
| Parametro | Simbolo | Valore Min | Valore massimo | Unità |
|---|---|---|---|---|
| Supply Voltage for Operation | VCI | -0.3 | 4.0 | V |
| Tensione Alimentazione per Logica | VDD | -0.5 | 2.75 | V |
| Tensione Alimentazione per Display | VCC | -0.5 | 19.0 | V |
| Temperatura di lavoro | TOP | -20 | +70 | °C |
| Temperatura di stock | TSTG | -30 | +70 | °C |
DC Caratteristiche elettriche
| Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
|---|---|---|---|---|---|---|
| Supply Voltage for Operation | VCI | － | 2.8 | 3.0 | 3.3 | V |
| Tensione Alimentazione per Display | VCC | － | 8.0 | 14.5 | 15.0 | V |
| Tensione Alimentazione per Logica | VDD | － | 1.65 | － | 2.6 | V |
| Ingresso Alto Livello | VIH | － | 0.8×VCI | － | VCI | V |
| Ingresso Basso Livello | VIL | － | 0 | － | 0.2×VCI | V |
| Uscita Alto Livello | VOH | Iout = 100uA | 0.9×VCI | － | VCI | V |
| Uscita Basso Livello | VOL | Iout = 100uA | 0 | － | 0.1×VCI | V |
| 50% Check Board Operating Current | VCC =14.5V | － | 15 | 30 | mA | |
Controller Pannello Touch FT3268
| Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
|---|---|---|---|---|---|---|
| Tensione Ingresso (Alta) | VIH | － | 0.7×VDD | － | VDD | V |
| Tensione Ingresso (Bassa) | VIL | － | -0.3 | － | 0.3×VDD | V |
| Uscita Alta Tensione | VOH | IOH = 0.1mA | 0.7×VDD | － | － | V |
| Uscita Bassa Tensione | VOL | IOL = 0.1mA | － | － | 0.3×VDD | V |
