REX012864D - レイスター株式会社 (Raystar Optronics, Inc.)

128x64 COG グラフィック 0.96インチ OLED 小型モジュール

Model No. REX012864D

REX012864D解像度は128x64 dots、0.96インチグラフィックタイプ COG OLED 小型モジュールです。外形寸法 26.7x19.26 mm。アクティブエリア (AA) 21.738x10.858 mm (0.96")。 SSD1306B ICが内蔵され、予めに6800インターフェースに設定し、8080、SPIとI2C にも対応可能です。動作温度範囲 -40~+80°C、保存温度範囲 -40~+85°Cです。自発光なので、バックライトが不要で、薄くて軽い、低消費電力が期待できます。しかも高いコントラスト比で、ウエアラブル端末に適しています。ZIF FPC とHot bar FPCがあります。表示色は白色、黄色とブルーがあります。★FPCの仕様について下記オプションの所をご参照ください。

仕様参考型番: REX012864DWPP3N00003

お問い合わせに追加/Demo Code

データシートダウンロード

戻る

項目	仕様	単位
構造	COG
サイズ(対角線)	0.96	インチ
ドットマトリックス / 解像度	128 × 64	ドット
モジュール寸法	26.7 × 19.26 × 1.26	mm
ビューイングエリア(VA)	23.938 × 12.058	mm
アクティブエリア(AA)	21.738 × 10.858	mm
ドットサイズ	0.148 × 0.148	mm
ドットピッチ	0.17 × 0.17	mm
表示色	OLED, 白色 / 黄色 / 青色
ディスプレモード	パッシブマトリクス
IC	SSD1306
インターフェス	6800, 8080, SPI, I2C
供給電圧	3V
Duty	1/64 duty
操作温度	-40~+80	°C
保存温度	-40~+85	°C
偏光板タイプ	偏光板オプション
FPC オプション	あり
タイプ	グラフィック型 OLED モジュール

No.

記号

功能

N.C. (GND)

Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

C2N

Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.

C2P

C1P

C1N

VBAT

Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.

VSS

Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.

VDD

Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.

BS0

Communicating Protocol Select
These pins are MCU interface selection input. See the
following table:

	BS0	BS1	BS2
I2C	0	1	0
3-wire SPI	1	0	0
4-wire SPI	0	0	0
8-bit 68XX Parallel	0	0	1
8-bit 80XX Parallel	0	1	1

BS1

BS2

CS#

Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.

RES#

Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.

D/C#

Data/Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data.
When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams.
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection.

R/W#

Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.

E/RD#

Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.

18~25

D0~D7

Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.

IREF

Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.

VCOMH

Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.

VCC

Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

VLSS

Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.

NC
(GND)

Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

REX012864D with Hotbar FPC

128x64 COG グラフィック 0.91インチ OLED 小型モジュール - REX012864D

REX012864D with ZIF FPC

128x64 COG グラフィック 0.91インチ OLED 小型モジュール - REX012864D

パラメーター	記号	最小値	最大値	単位
Supply Voltage for Logic	VDD	0	4.0	V
Supply Voltage for Display	VCC	0	15.0	V
操作温度	TOP	-40	+80	°C
保存温度	TSTG	-40	+85	°C

項目	記号	条件	最小値	典型値	最大値	単位
Supply Voltage for Logic	VDD	－	2.8	3.0	3.3	V
Supply Voltage for Display	VCC	－	11.5	12.0	12.5	V
Input High Volt.	VIH	－	0.8×VDD	－	VDDIO	V
Input Low Volt.	VIL	－	0	－	0.2×VDD	V
Output High Volt.	VOH	－	0.9×VDD	－	VDDIO	V
Output Low Volt.	VOL	－	0	－	0.1×VDD	V
Operating Current for VCC (50% display ON)	ICC	Vcc =12V	－	16	20	mA

FPC オプション

FPC Length	PIN	Pitch	ZIF / HOTBAR FPC	インターフェス	FPC No.	Create Date
22	30	0.7	HOTBAR	6800,8080,SPI,I2C	FPC2070003001XXXXX08	20170808
41.1	30	0.5	ZIF	6800,8080,SPI,I2C	FPC2050003011XXXXX28	20180604
13.1	30	0.5	ZIF	6800,8080,SPI,I2C	FPC2050003011XXXXX34	20200221