- 仕様
- ピン配置
- 外形図
- 絶対最大定格
- 電気特性
| 項目 | 仕様 | 単位 |
|---|---|---|
| 構造 | COG | |
| サイズ(対角線) | 0.96 | インチ |
| ドットマトリックス / 解像度 | 128 × 64 | ドット |
| モジュール寸法 | 24.74 × 16.90 × 1.26 | mm |
| ビューイングエリア(VA) | 22.74 × 11.86 | mm |
| アクティブエリア(AA) | 21.74 × 10.86 | mm |
| ドットサイズ | 0.15 × 0.15 | mm |
| ドットピッチ | 0.17 × 0.17 | mm |
| 表示色 | OLED, 白色 / 黄色 | |
| ディスプレモード | パッシブマトリクス | |
| IC | SSD1315 | |
| インターフェス | 3線式/4線式 SPI / I2C | |
| 供給電圧 | 3V | |
| Duty | 1/64 duty | |
| 操作温度 | -30~+70 | °C |
| 保存温度 | -30~+70 | °C |
| 偏光板タイプ | 偏光板オプション | |
| タイプ | グラフィック型 OLED モジュール |
| Pin No. | 記号 | 功能 | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 1 | C2N | C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor. | ||||||||
| 2 | C2P | |||||||||
| 3 | C1P | C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor. | ||||||||
| 4 | C1N | |||||||||
| 5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used. |
||||||||
| 6 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. When charge pump is enabled, a capacitor should be connected between this pin and VSS. |
||||||||
| 7 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
||||||||
| 8 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
||||||||
| 9 | BS0 | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
|
||||||||
| 10 | BS1 | |||||||||
| 11 | CS# | Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. |
||||||||
| 12 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
||||||||
| 13 | D/C# | In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
||||||||
| 14~16 | D0~D2 | When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||
| 17 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA. |
||||||||
| 18 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||||
| 19 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. When charge pump is enabled, a capacitor should be connected between this pin and VSS. |
||||||||
| 20 | VLSS | Ground of Analog Circuit This is an analog ground pin. It should be connected to VSS externally. |
| パラメーター | 記号 | 最小値 | 最大値 | 単位 |
|---|---|---|---|---|
| ロジック電源電圧 | VDD | -0.3 | 4.0 | V |
| チャージポンプレギュレータ | VBAT | -0.3 | 6.0 | V |
| ディスプレイ電源電圧 | VCC | 0 | 18.0 | V |
| 操作温度 | TOP | -30 | +70 | °C |
| 保存温度 | TSTG | -30 | +70 | °C |
DC 電気特性
| 項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
|---|---|---|---|---|---|---|
| ロジック電源電圧 | VDD | － | 2.8 | 3.0 | 3.3 | V |
| ディスプレイ電源電圧 | VCC | － | 7.0 | 7.5 | 8.0 | V |
| 入力電圧（High） | VIH | － | 0.8×VDD | － | VDD | V |
| 入力電圧（Low） | VIL | － | 0 | － | 0.2×VDD | V |
| 出力電圧（High） | VOH | － | 0.9×VDD | － | VDD | V |
| 出力電圧（Low） | VOL | － | 0 | － | 0.1×VDD | V |
| VCC 動作電流 (50% Display On) | ICC | － | － | 6 | 12 | mA |
