REX012864M OLED Gráfica Bicolor

Especificación
Función Interfaz Pin
Dibujo del Contorno
Valores Nominales Máximos Absolutos
Características Electrónicas

Elemento	Dimensión	Unidad
Estructura	COG
Tamaño (Diagonal)	0.96	pulgada
Matriz de puntos (Resolución)	128 × 64	dots
Dimensión del módulo	26.7 × 19.26 × 1.26	mm
Área de visión	23.744 × 13.204	mm
zona activa(AA)	21.744 × 11.204	mm
Tamaño del punto	0.148 × 0.148	mm
Distancia entre puntos	0.17 × 0.17	mm
Color de Emisión	OLED, Amarillo & Azul cielo (doble color)
Modo de visualización	Matriz Pasiva
IC	SSD1306
Interfaz	8080 / 6800 / SPI / I2C
Fuente de alimentación	3V
Deber	1/64 Deber
Temperatura de funcionamiento	-40~+80	°C
Temperatura de almacenamiento	-40~+85	°C
Tipo de polarizador	Polarizador opcional
Tipo	Pantalla Gráfica OLED, doble color OLED Pantalla

Pin No.

Símbolo

Función

N.C. (GND)

Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

C2N

Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.

C2P

C1P

C1N

VBAT

Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.

VSS

Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.

VDD

Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.

BS0

Communicating Protocol Select
These pins are MCU interface selection input. See the
following table:

	BS0	BS1	BS2
I2C	0	1	0
3-wire SPI	1	0	0
4-wire SPI	0	0	0
8-bit 68XX Parallel	0	0	1
8-bit 80XX Parallel	0	1	1

BS1

BS2

CS#

Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.

RES#

Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.

D/C#

Data/Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data.
When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams.
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection.

R/W#

Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.

E/RD#

Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.

18~25

D0~D7

Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.

IREF

Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA.

VCOMH

Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.

VCC

Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

VLSS

Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.

NC
(GND)

Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

REX012864M OLED Gráfica Bicolor - Raystar - Dibujo del Contorno

Parámetro	Símbolo	mínimo	Máximo	Unidad
Tensión de Alimentación para lógica	VDD	0	4	V
Suministro de voltaje regulado para la bomba de carga	VBAT	-0.3	5.0	V
Tensión de alimentación de la pantalla	VCC	0	16.0	V
Temperatura de funcionamiento	TOP	-40	+80	°C
Temperatura de almacenamiento	TSTG	-40	+85	°C

Características Electrónicas DC

Artículo	Símbolo	Condición	mínimo	Típico	Máximo	Unidad
Tensión de Alimentación para lógica	VDD	－	2.8	3.0	3.3	V
Tensión de alimentación de la pantalla (Supplied Externally)	VCC	－	11.5	12	12.5	V
Voltaje de alimentación del regulador de la bomba de carga	VBAT	－	3.0	－	4.2	V
Voltaje de salida de la bomba de carga para la pantalla (Generated by Internal DC/DC)	Bomba de carga VCC	－	7.0	7.5	－	V
Entrada de alto tensión	VIH	－	0.8×VDD	－	VDD	V
Entrada de baja tensión	VIL	－	0	－	0.2×VDD	V
Alta tensión de salida	VOH	－	0.9×VDD	－	VDD	V
Baja tensión de salida	VOL	－	0	－	0.1×VDD	V
Operating Current for VCC (50% display ON) (VCC Supplied Externally)	ICC	VCC =12V	-	9	13.5	mA
50% check Board Operating Current (VCC Generated by Internal DC/DC)	IBAT	－	－	15	25	mA